If you want a 'real' Altimeter, look no further. No GPS used here.

Learn how a real pressure Altimeter works such as you would find in an aircraft. Altimeter for Aviators is primarily designed as an Apple Watch application, although it does also work on iPhones or iPads that have a barometer. Provided your watch has a Barometer it will even run stand-alone (no iPhone needed).

Student and instructor pilots will find this App to be a valuable training tool, while those knowing how to use an altimeter will enjoy having it on their wrist.

To obtain your Altitude (height above sea level):
Set the 'pressure setting' to the current air pressure at sea level. Weather forecasts often give this (eg the BBC Weather App includes pressure in mb). You can also obtain the pressure from weather pressure charts or from METAR reports from airports (eg Q1017). In aviation speak, this is known as the QNH. Set the pressure setting by rotating the 'crown' on your watch. You can then 'Lock' this setting so you don't accidentally change it by doing a long-press and choosing 'Lock'. Alternatively, if you know the altitude of the point that you are currently at, you can rotate the watch crown until the Altimeter reads the correct altitude.

To obtain your height above a certain location:
Set the 'station' pressure for that location (the actual air pressure at that very point). Aviation language calls this pressure setting QFE. If you are at that location, you can just rotate the crown of the watch until the Altimeter reads zero. As a short-cut you can alternatively long-press and then pick "Zero (QFE)".

To obtain your Flight Level (FL):
Another setting that pilots use is the standard setting of 1013.25mb. This is used above 3000ft roughly and instead of giving you an accurate 'Altitude' gives you what is known as a 'Flight level'. Long-press and select the "STP (FL)" option as a short cut (FL stands for Flight Level. STP stands for 'Standard Temperature and Pressure').

If you are more familiar with inches of mercury (inHg) rather than hectapascals (hPa) or millibars (mb) then toggle this with the 'Units' menu item. Note that mb and hPa are the same unit.

Your watch (or iPhone) pressure sensing device has not been calibrated in the same way that the expensive altimeters found in aircraft have been. Your electronic device also has more points of failure and error being miniature and electrically based so this App in no way replaces or can be used for actual flying. If you run this App side by side on two different iOS devices, the chances are they'll give you slightly different altitudes. Further, if you're a pilot the pressure in your cockpit is unlikely to be as accurate as the location of the static pitot tube and will be susceptible to changes due to air vents being opened, doors with gaps, any climate control, your speed and any vibration.

Air pressure changes throughout the day can cause readings to drift by up to 1 foot per minute, so keep the pressure-setting up-to-date by updating it whenever you can; as you get to any locations of known altitude or hourly if receiving pressure settings in some other way.

Altimeter for Aviators shows how recent the altitude was calculated (it's not constant)
White = updated in the last 10 seconds
Yellow = updated between 10 and 60 seconds ago.
Pink = updated between 1 and 10 minutes ago.
Dark Red = updated more than 10 minutes ago.

Altitude units:
The long hand shows 100s of feet. The short hand 1000s of feet. The inward pointing edge arrow shows 10000s of feet. The barber pole (stripe at the bottom) is visible below 10000 feet, so if it disappears you are at risk of Hypoxia.

What’s New

Version 2.3.2

Stability improvement and minor bug fixes in Watch component.

Ratings and Reviews

4.8 out of 5
39 Ratings

39 Ratings

AndyDurham10 ,

Best altimeter app bar none.

I fly and this is accurate. However, can we have the option for whole Hpa increments when swiping up/down on the altimeter, instead of .25 .5 .75 and .0 ?

Very good !

Developer Response ,

Thank you for taking the time to leave such kind feedback. Your suggestion has also been noted. Thank you.
Safe flying.

Nickle001 ,


Looks good.
1. Pressure setting is all driven off mg. if you change units it still increments in mg steps
2. Should have a choice of feet or meters
3 similar for rate of climb. Meters per second. 100s of feet, knots are all used
4. 30s average climb is another option.
5. You know where the phone is from gps. That means you can look up local pressure and set that automatically. There are services for this.
6. Barometer or gps should be an option
7. Gps height compared with barometer height gives local pressure if you can’t get a service
Just some ideas

Developer Response ,

Very perceptive, accurate feedback. Thank you.

App Privacy

The developer, STEARsoft, indicated that the app’s privacy practices may include handling of data as described below. For more information, see the developer’s privacy policy.

Data Not Collected

The developer does not collect any data from this app.

Privacy practices may vary based on, for example, the features you use or your age. Learn More


  • Family Sharing

    Up to six family members will be able to use this app with Family Sharing enabled.

More By This Developer

You Might Also Like