REALITi 17+

**New Features**

CPR Ventilation Monitor

* Added scaling on ventilation bars based on manikin type or parameter settings.
* Added numeric label for max volume based on manikin type or parameter settings.
* Incl. a line for each max volume and set at 90% of the full scale.
* Enabled clipping of values greater than full scale.

CPR Depth Monitor

* Added CPR depth configuration from Control on Zoll X Series, Zoll X Advanced, Zoll Propaq MD, Corpuls 3, Zoll R Series, Generic Defib and CPR Console.
* Enabled conversion of units for compression depths.
* Improved CPR bar displays for compression depths.
* Adjusted CPR bars to match CPR depth values.
* Fixed monitor with CPR device crashing upon connection with Control.

CPR Depth Control / Facilitator

* Added CPR depth configuration in Parameter Settings
* Added conversion of units for Adequate Depth.
* Added conversion of units for Max. Depth.
* Added CPR manikin type drop down option for Automatic, Newborn, Child and Adult.

CPR Depth

* Fixed compression depth values not updating properly when switching to another monitor.
* Fixed issue on adequate compression depth value not displayed in the correct level.
* Fixed monitor crashing when switching to other monitors while Atlas Junior is connected.
* Corrected Corpuls3 and Corpuls 3T values showing zeros instead of the default values.

**Improvements**

Atlas

* Increased length of low RR CO2 when using SimConnect or Atlas manikin for ventilation.
* Fixed Atlas CPR not affecting HR.
* Added manikin data recording (Currently debug builds only)
* Added CPR depth configuration from Control on Zoll X Series, Zoll X Advanced, Zoll Propaq MD, Corpuls 3, Zoll R Series, Generic Defib and CPR Console. Enabled conversion of units for compression depths. Improved CPR bar displays for compression depths. Adjusted CPR bars to match CPR depth values.
* Added partial support for Atlas Baby.
* Fixed AED not working from “movement detected” due to compressions state not ending.
* Made connect process for Atlas Junior same as in 11.6.0.
* Cap data of Atlas Junior.
* Added extra values in Atlas Junior compression lookup table.

Corpuls 1

* Fixed Hamilton T1 where the alarm continues after quitting a scenario.
* Corrected therapy socket influence on electrodes.

Corpuls 3/3T

* Fixed issue with metronome count not reverting to original configured ratio.
* Fixed issue with Start Analysis being played just after powering on, no delay.
* Fixed issue with metronome not resetting to Adult 30:2 when C3/C3T is powered off.
* Fixed memory leak in Corpuls 3/3T which resulted in a crash when used with Hamilton T1.

Defigard Touch 7

* Added parameter field flash on NIBP, Temp, ETCO2 and RR when values are off limits.
* Enabled flash on bigger NIBP field.
* Improved priority alarms to show in the alarm status field properly.
* Corrected precedence of alarm message from any parameter over “ECG: Cable not detected” message.
* Added “ECG: VF/VT” if HR alarm still persists for a certain period of time for any patient type.
* Included “ECG: Asystole” message when HR is 0\.
* Improved alarm light to change from orange to red if alarm is for VF, VT or Asystole.
* Improved alarm light to show orange for medium and low alarms.
* Fixed Pulse field not flashing when pulse is off limits.
* Fixed “SpO2: Pulse off limits” message issue from not appearing when there is a pulse rate alarm.
* Integrated pulse alarm limits to the alarms; value on the pulse will now determine whether to show the alarm based on these limits.

Hamilton T1

* Fixed Hamilton T1 where the alarm continues after quitting a scenario.

Multiple Monitors / Screens

* Fixed the additional monitor not showing the correct state of pleth based on the primary monitor.
* Fixed ECG waveform not being changed if the new waveform was the same as the previously loaded scenario.

Zoll R

* Fixed Filtered ECG not getting deactivated by Control.