AxisForge

CNC & Laser Remote Control

Only for iPhone

Free · Designed for iPhone. Not verified for macOS.

iPhone

The most responsive CNC pendant on your iPhone. Native Taptic Engine haptics, instant touch response, and a safety system built for the shop floor. AxisForge turns your iPhone into a professional wireless jog pendant for your CNC router or laser cutter — no dedicated hardware remote needed, just your phone and the AxisForge USB dongle. WORKS WITH YOUR SOFTWARE Built-in profiles for the most popular CNC and laser software — no configuration needed: Carbide Motion Universal G-Code Sender (Mac & Windows) Easel by Inventables Mach3 OpenBuilds CONTROL Generic GRBL LightBurn Custom Layout — assign any key combination to any button DESIGNED FOR THE SHOP FLOOR Large, glowing jog buttons you can tap confidently with work gloves on ARM/DISARM safety system — buttons only send keystrokes when intentionally armed Deadman mode — hold the ARM button to keep jogging; release and the machine stops instantly Automatic watchdog: if your phone disconnects mid-jog, the dongle stops all movement within 500ms Auto-disarms when you navigate away from the jog screen — no accidental moves Hold-to-jog mode for continuous movement, or tap mode for precise incremental steps 5 increment presets: 0.01 / 0.1 / 1 / 10 / 25 mm Feed rate selector: Slow / Med / Fast FEED HOLD always reachable — even when disarmed INSTANT RESPONSE Jog commands fire the instant your finger touches the button — not on lift Hold-to-jog starts immediately on first touch with zero delay HAPTIC FEEDBACK BUILT FOR THE SHOP Talks directly to the native Taptic Engine for zero-latency response Four feel presets: Smooth, Click, Punch, and Machine — from subtle to industrial Press Kick intensity: Off, Tiny, Light, Medium, Heavy, or Hardcore Smooth continuous hold buzz powered by Core Haptics — one clean waveform for the entire hold, no ticking Hold Speed control: dial in when the buzz starts, from a relaxed delay to instant on first touch SIMPLE SETUP Plug the AxisForge USB dongle into your CNC or laser computer Open the app — it finds the dongle automatically over Bluetooth Pick your software profile ARM and start jogging The dongle acts as a USB keyboard to your computer — no drivers, no software install, no admin rights needed. It just works. THE DONGLE The AxisForge wireless dongle is sold separately at TheBossFactory.ca and Etsy. The app is free. AxisForge is not affiliated with or endorsed by Carbide 3D, Inventables, LightBurn Software, Newfangled Solutions, OpenBuilds, or any other software manufacturer.

Ratings & Reviews

  • This app hasn’t received enough ratings or reviews to display an overview.

What's New Connectivity New Connected status screen shows signal strength and connection quality before jogging Auto-sync active profile to dongle on every reconnect — no need to re-select your software Smart reconnect routing — returns directly to jog screen if software was previously selected Forgetting a dongle now correctly resets the saved software profile Jogging & Controls Jog commands fire on touch-down instead of finger lift — significantly lower latency Fixed stuck axis issue when holding multiple buttons simultaneously Instant hold-to-jog response — no delay between press and movement Arm prompt appears when tapping increment or speed bar while disarmed Deadman mode toggle updates the ARM banner instantly Haptics Full haptic redesign: style (Punch, Buzz, Click), speed (Slow / Normal / Fast / Instant), and press-kick intensity (Off → Hardcore) Continuous hold buzz via Core Haptics with adjustable amplitude Pre-warmed haptic generators for zero cold-start latency Haptic state correctly restored after app resume Keyboard Profiles — Verified & Fixed Keyboard shortcuts verified against official documentation for all supported CNC software Generic GRBL: Feed Hold now sends !, Resume sends ~ — matching the GRBL real-time command spec OpenBuilds CONTROL: removed incorrect Space mapping from Feed Hold (Space starts a job) LightBurn: removed incorrect Escape mapping for stop job App Polish What's New sheet shown on first launch after each update App Store review prompt after 3+ jog sessions Bug report screen with screenshot attachment Scan screen forgets unavailable dongles automatically UI cleanups, animation improvements, and performance fixes throughout

Version 1.0.24

The developer, Francis Bosse, indicated that the app’s privacy practices may include handling of data as described below. For more information, see the developer’s privacy policy .

  • Data Not Collected

    The developer does not collect any data from this app.

    Privacy practices may vary, for example, based on the features you use or your age. Learn More

    Accessibility

    The developer has not yet indicated which accessibility features this app supports. Learn More

    Information

    Seller
    • Francis Bosse
    Size
    • 33.4 MB
    Category
    • Utilities
    Compatibility
    Requires iOS 13.0 or later.
    • iPhone
      Requires iOS 13.0 or later.
    • iPod touch
      Requires iOS 13.0 or later.
    • Mac
      Requires macOS 11.0 or later and a Mac with Apple M1 chip or later.
    • Apple Vision
      Requires visionOS 1.0 or later.
    Languages
    • English
    Age Rating
    4+
    Copyright
    • © The Boss Factory
  • Developer Website
  • Privacy Policy

    • You Might Also Like