Added a link to instructions for creating an ultrasonic transducer test target tank.

This version adds display of test ping TOF values, and better validation of best frequencies for transducer installations.

This version has minor improvements to the transducer calibration process and the Test Monitor Page.

Monitor Test page facilitates testing monitors in inventory before re-deployment.

New Monitor Status page allows user to check latest message on my.xactmonitoring.com and allows Zone Managers and Company Admins to change Status of monitor. Fixed bug in Reset to Factory Defaults page.

This version has adjustments for scoring transducer pings and fixes the Fill percent item in Verify Settings.

This version changes the Transducer Assist Page to use most common settings for testing and increases burst width (energy) for large tanks. It also resolves a bug that caused the app to hang when updating Location Name and Schedule.

Version 2.3.4 resolves a bug that caused Transducer Position Assist to hang when querying the transducer temperature.

Version 2.3.2 is a critical update for users installing monitors with ultrasonic transducers. Version 2.3.2 has a new algorithm for analyzing transducer ping packets. This resolves situations where the installation would fail in the Transducer Position Assist page. The manual settings for the transducer also have been restored to this page. If the Transducer Position Assist fails 3 times, the user is given the option to use Manual Signal Tuning. These settings include: Known fill percent(Target TOF), Clamp time, Delay time, Burst width, and Gain.

This version fixes a bug that caused the camera to remain on after tapping the Back button from the QR Scanner page.

Framework update to keep parity with Android version.

* Update monitor log entries. * Added known fill level to Transducer Position Assist page for more accurate echo detection. * In Verify Commission page, marked previous commissions from same monitor as superseded to reduce confusion. * App now generates commission message and downloads to monitor to facilitate future updates to commission message. * Fixed progress bar on TPA page. * Expanded acceptable TOF for frequency search to 1 StdDev. * Serial comms update for monitor firmware version 4.37

This version fixes a bug that caused the app to hang at "Updating products..." after logging in.

Support for Products. Various UI bug fixes.

This version fixes a bug when the calibration offset was negative in gauge reader calibration page.

Fixes timeout bug with firmware version 4.30.

New tank types for specific customers.

This version fixes a bug with converting circumference to diameter in Transducer Position Assist.

* Viewable, copyable monitor log for monitors running F/W version >= 4.31. * Made Transducer Position Assist the default behavior for transducer installations. * Implemented Listen Delay input in Transducer Position Assist to mask out echoes from sludge/sediment boundaries. * Implemented Temperature input in Transducer Position Assist to verify sensor function. * Display cellular radio carrier and signal metrics in Verify Settings.

* Viewable, copyable monitor log foransducer Position Assistr monitors running F/W version >= 4.31. * Made Transducer Position Assist the default behavior for transducer installations. * Implemented Listen Delay input in Transducer Position Assist to mask out echoes from sludge/sediment boundaries. * Implemented Temperature input in Transducer Position Assist to ensure sensor function. * Display cellular radio carrier and signal metrics in Verify Settings.

Transducer Position Assist page uses foot/inch (meter/CM) entry fields instead of foot/decimal slider. This makes it consistent with the Tank Dimensions page and makes it easier to enter foot/inch values instead to foot/decimal values for tank diameter.

This update is designed to leverage the power management updates in controller firmware version 4.22 which has better power management for monitors with ultrasonic transducers. It is backward compatible with older versions of controller firmware (less than or equal to 4.21).

This version has a lower battery threshold (5.5v) for ultrasonic transducer installations.

Added QR code scanner to connect to XACT Wi-Fi. Various bug fixes to eliminated errors.

Version 2.2.34 fixes an error when configuring monitors with satellite radios where the serial number is greater than 0-4299999.