New: • Better OlenPack support, incl. BMS activation (≥2c2c); • Battery presence expiration is configurable (≥2c24); • Battery lost message can be not shown as it is configurable (≥2c24); • Cluster idle & balance (charging/discharging) state current limits are now configurable (≥2c2c). Miscellaneous improvements and fixes.

New: • Bulk label generation (≥2c02); • Enhanced radar (≥2c02) • Gen-2 BMS configuration update system (v1); • Femto DFU mode is integrated for expert users; Fixes : • Battery label generation for old batteries; • "Battery" tab was selected despite the user made another choice at the very start of the device connexion. Miscellaneous improvements and fixes.

• Added new technical support features.

• Fix display of "Prevent non expert user to change those settings" for SoC protection; • Board temperature is now only displayed in expert mode.

Fixed alarm for HLK B20 batteries.

Fixed support for HLK B20 batteries which was broken before.

Additions: • Experimental support for second-generation BMS alarms; • Support for switching to Femto mode; Miscellaneous improvements and fixes.

Added: • BMS key role : Same list as PC software; • Backward compatibility for former solo heating system (before SBM 14); • Support for dual heating systems w/ NTCs usage (SBM 14+ and ≥ 2bd2); • Support for SoC settings (≥ 2bd1); • Pepsr firmware update via Pepsr Femto over WiFi; • Support for external BMS screen and its enable and hibernation delay settings (≥ 2bca); Miscellaneous improvements and bug fixes.

Added: • Heat MOS temp (≥ 2bbe) on SBM 13; • Device ID sheet reduced to 80% in size; • External temperature sensors support (≥ 2bbb); • Gen-2 heating system with CAN bus request (> 2bba); • PC section in BMS; • Restart and shutdown BMS system; • High speed UART BMS support (≥ 2baf) ; • Preliminary remote control support; Fixes: • SoO C-rate min limited to 1.1; • Added production date support for gen-2 BMS; • SoC settings changes were almost impossible; Miscellaneous improvements and bug fixes.

• Merlin: new relay scenario "At power on, trigger a relay, after a delay" available (> 2ba8); • Better explanation about battery seal vs config fix; • Miscellaneous improvements and bug fixes.

• Fixes: • BMS force switch & active balancing in RO; • Overload visualisation; • BMS edition for decimals; • issue on some input field that was not accessible on small screen; • Added: • Build number persistence for serial updates; • EV state for NOIL vehicle; • OCV curves visualisation + realtime SoC for min/max cell voltages; • battery optimisation state visualisation; • 3-light system documentation for OlenMove XS One; • Overload state representation for Merlin; • Handle absent or malfunctioning temperature sensors; • Miscellaneous improvements and bug fixes.

• Support for representing the overload status of the Merlin; • Support for the absence and deterioration of temperature sensors; • Support for the absence and deterioration of temperature sensors; • The BMS tab header is now retractable; • Fixed an issue preventing the entry of decimal numbers in the BMS configuration; • Fixed an issue preventing the retrieval of the firmware file from the cloud for updates; • Support for local sealing (respectively unsealing) of the BMS configuration, preventing (respectively allowing) any modification of its configuration (≥2b8f); • Added LBY to the team; • Overload protection can be disengaged (≥ 2b8d); • Various corrections: Baud rate, scenarios; • Forced commands for the "lights"; • Support for equipment control mode "Beeper and 3 lights" (≥ 2b87); • Fixed a connection issue with the demonstration Merlin; • Support for the coupling functions of Merlin OlenMove XS and auxiliary refueling units and related settings (≥2b7e); • Fixed a problem preventing the display of the status of Merlin relays; • Other improvements and bug fixes.

• Fix an issue preventing a battery to be withdrawn from a cluster; • Miscellaneous improvements and bug fixes.

Extended support for OlenMove storage systems and its 3-light alarm system.

• BLE firmware upgrade: better end of process feedback; • Locked battery: Added chemistry mismatch; • Gen 2 support + health history & export; • Miscellaneous improvements and bug fixes.

• Fixed SoO gauge which didn't always continuously updates; • Miscellaneous improvements and bug fixes.

• Better BLE connection; • Better BMS value update; • Fix BMS config and FU mode: check battery state before to proceed; • BMS configuration management (≥ 2b3b); • Miscellaneous improvements and bug fixes.

• Downstream KPIs in msg/s in evolution curves; • Current detection investigation (b2b05); • Current collection in settings (b2af1); • Evolution data are now collected straight from the connection; • BUSY withdrawn from the radar; • Relay v3: support (wip); • OlenMove deep discharge system; • Force HW PCB rev settings in production (2ae3); • Shows scenario presence in at glance; • High performance mode: added lock settings for non expert users (b2ae0); • Miscellaneous improvements and bug fixes.

• Smartbox DFU : with force flavor; • Under voltage detection settings (b2adc); • Battery high performance mode level adjusted (b2acf); • Cluster migration (Merlin 2ad9); • Fixed device role not displayed; • Radar: Fixed SoC and state display issue; • Smartbox DFU: Fixed issue that makes DFU very slow; • At Glance: repair of a problem reporting 1 more error (under voltage) than reality; • Miscellaneous improvements and bug fixes.

• Expert mode has access to device role management; • Battery high performance mode (b2ad6); • Radar : Expandable cluster; • CANbus: Traffic layer generator for OE & Ion (Victron coming soon) (b2abf); • Smartbox language support (b2abc); • Settings: App / Langue : Force les English acronyms; • Firmware build disparity support (b2abb); • SoO v3 RC3: internal state vizu for Merlin (b2aba); • Miscellaneous improvements and bug fixes.

• Device deconnection notification; • Added capacity evolution; • CANbus & UART speed configuration/b2a8b ; • Factory reset/b2a81; • Investigation mode/b2a81; • Listing of connecting batteries; • Added MOS state in evolution; • Fixed an issue where SoC protection dashboard wouldn't shows up in battery tab;, • Fixed negative current fetched from Smartshunt; • Smartshunt: higher resolution support for current and capacity/b2a7d; • Miscellaneous improvements and bug fixes ;

• Performance improvement; • Support for the SoH; • Better support for the Smartshunt; • Support for the type of current (with inverter/charger); • Miscellaneous improvements and bugs fixes.

• Improved graphical dashboard; • Radar UI overhaul for better cluster exposure; • Support for better SoO; • Support for battery location; • And many other things!

• Battery location is now displayed; • Undervoltage threshold scheme updated for L1 and L2; • Enhanced Battery glance; • Weather conditions ; • Location by Bluetooth contact; • Better radar staging; • Showing the activation or deactivation of the battery lock; • Added battery lock reason to dialog; • Various improvements and fixes.

• Battery location is now displayed; • Undervoltage threshold scheme updated for L1 and L2; • Enhanced Battery glance; • Weather conditions ; • Location by Bluetooth contact; • Better radar staging; • Showing the activation or deactivation of the battery lock; • Added battery lock reason to dialog; • Various improvements and fixes.