PhosphorRTTY
Dienstprogramme
Nur für iPhone
0,99 € · Entwickelt für iPhone
iPhone
PhosphorRTTY decodes Radio Teletype (RTTY) signals in real time using your iPhone's microphone. Hold your phone near a shortwave radio tuned to an RTTY signal and watch the text appear on screen, character by character, on an authentic phosphor CRT display.
No internet connection required. No external hardware. No account. Just your iPhone and a radio.
WHAT IT DECODES
RTTY is the oldest digital mode in amateur radio — two audio tones representing mark and space, encoding text via the 5-bit ITA2 (Baudot) alphabet or 7-bit ASCII. PhosphorRTTY handles all standard configurations:
Baud rates: 45.45, 50, 75, 100 Bd (auto-detected or manual)
Shifts: 85, 170, 450, 850 Hz (auto-detected or manual)
ITA2 (Baudot) and ASCII modes
USB and LSB conventions
AUTOMATIC SIGNAL DETECTION
The app automatically finds and locks onto RTTY signals:
AFC (Automatic Frequency Control) acquires and tracks drifting signals
Auto-baud detection identifies the transmission speed
Auto-shift detection determines the frequency separation
Squelch suppresses noise when no signal is present
Or disable any of these and tune manually for full control.
FOUR TABS
DECODE — The main teleprinter display. Decoded text appears character by character with an authentic mechanical delay. Status bar shows baud rate, shift, mark/space frequencies, and signal lock state. Clear, pause, and session controls.
SIGNAL — Live signal analysis. FFT spectrum display (0–4 kHz), scrolling waterfall, mark/space tone indicators, bit period histogram with baud rate markers, and a paper punch tape visualisation of the decoded data stream.
LOG — Session history. Every decode session is saved with timestamp, duration, character count, and the full decoded text. Copy, share, or delete individual sessions.
CONFIG — All parameters. Audio input gain, decode mode (auto/manual for baud, frequency, and shift), display theme, font size, bell character handling, and RYRY sequence display options.
THE DISPLAY
Two authentic phosphor CRT themes:
Amber (classic teleprinter terminal)
Green (military/commercial terminal)
Both feature horizontal scanlines, edge vignette, and phosphor glow effects.
Monospaced font throughout. RYRY test sequences can be dimmed or hidden to keep the display clean.
DSP ENGINE
The signal processing is done entirely on-device using a per-sample I/Q quadrature demodulation pipeline:
Biquad low-pass filtered I/Q channels for each tone
W7AY Automatic Threshold Correction for bit decisions
Digital Phase-Locked Loop (DPLL) with per-transition phase correction for timing recovery
512-point FFT for frequency analysis and AFC
Asymmetric envelope detection for robust tone tracking through fading
Tested against real over-the-air recordings from 20m and 40m amateur bands. Under 1% error rate on clean signals, 4–5% on moderate HF conditions with fixed tuning.
WHERE TO FIND RTTY
Amateur radio: 14.080–14.099 MHz (20m band), 7.080–7.100 MHz (40m band), 21.080–21.100 MHz (15m band). RTTY contests run throughout the year — during a contest, these frequencies are packed with signals.
Maritime and commercial RTTY transmissions can be found across the HF spectrum. A shortwave receiver or SDR with audio output is all you need.
REQUIREMENTS
iPhone with microphone
iOS 17 or later
A radio receiver tuned to an RTTY signal (shortwave radio, SDR, or WebSDR audio played through a speaker)
No in-app purchases. No subscriptions. No tracking. No network access.
Bewertungen & Rezensionen
Diese App hat noch nicht genügend Bewertungen oder Rezensionen erhalten, um eine Übersicht anzuzeigen.
Das Entwicklungsteam, Stuart Woolley, hat darauf hingewiesen, dass die Datenschutzrichtlinien der App den unten stehenden Umgang mit Daten einschließen können. Weitere Informationen findest du in den Datenschutzrichtlinien des Entwicklungsteams .
Keine Daten erfasst
Der Entwickler erfasst keine Daten von dieser App.
Bedienungshilfen
Der Entwickler hat noch nicht angegeben, welche Bedienungshilfen diese App unterstützt. Weitere Infos
Informationen
- Größe
- 2,7 MB
- Kategorie
- Dienstprogramme
- Kompatibilität
Erfordert iOS 26.2 oder neuer.
- iPhone
Erfordert iOS 26.2 oder neuer. - Mac
Erfordert macOS 26.2 (oder neuer) und einen Mac mit Apple M1-Chip (oder neuer). - Apple Vision
Erfordert visionOS 26.2 oder neuer.
- Sprachen
- Englisch
- Altersfreigabe
4+
- 4+
- Anbieter
Stuart Woolley
- Stuart Woolley hat sich nicht als Händler für diese App ausgewiesen. Falls du Verbraucher:in im Europäischen Wirtschaftsraum bist, gelten die Verbraucherrechte nicht für Verträge zwischen dir und dem Anbieter.
- Copyright
- © 2026 Stuart Woolley
