* Fix for network scanning view not showing nearby public networks

* Internal changes in preparation for future features * Improvements to prevent status bar from covering UI components * Adds safeguards in network management view to prevent crashes when receiving invalid inputs * Fix for incorrect load cell labels with SmartScale add-on units. ** Names were 'Front/Back' instead of 'Left/Right'

* Full SmartFeed Ultra support ** Voltage readout is now working ** Door state information is now correct ** 'STOP' button should now trigger a 'jam' behavior and stop the motor ** All features should be working now * Replaces 'Not Uploading' with 'Idle' as the message when a unit is not currently uploading data * Help and Service Mode menus are now fully scrollable, should help with extremely small screens.

* Minor styling changes to improve consistency of display across devices * New unit type simulator support (experimental, likely changes in next version(s))

* internal permissions changes ** no behavioral/display changes

* Improved Network Management UI to prevent modal dialog from extending off screen. * Keyboard auto-hides in Network Management modal when tapping off of a text input.

* Fix a UI regression in the network management view that makes it harder to see the fields when adding a network

* adds support for displaying/triggering auto-recoveries from the GF view without connecting directly to the auto-recovery box * fixes some error handling behaviors to remove some warnings and ensure error dialogs are always shown when something goes wrong while scanning * improved support for newer products/configurations

* Improvements to readability of network management modal dialog. ** Adds shading to distinguish fields from the background ** Increases font sizes ** Adds labeling for some fields

* Fixes inconsistencies with product names throughout the application * Adds official product name for 'SimpleScan' units. * Adds support for BLE enabled dish heater units ** Allows viewing live thermistor, temp, relay, and error status ** Allows sending on/off commands for relays (may be overridden by temp settings on the dish) ** Allows configuring the WiFi/FID settings for the dish unit

* Add support for new systems * Adjust default auto-recovery duration (300 sec -> 120 sec) * Add visual feedback to auto-recovery run button

* Adds support for auto-recovery system * Adds support for auto-start generator system * Adds simulated interfaces for newly supported systems

* Changes to service/setup mode to allow (re-)configuration of new model units * Minor UI changes to improve readability on some screens

* Compatibility fixes with old firmware * Fix for rare crashes when scanner finds a Bluetooth device with an empty service list.

* Fix for Incompatible Version screen, previously would display the launch screen and/or a white screen. ** Adds a simulated view for this error screen in the help menu * Improved logging for connections ** logs remain accessible through the 'view logs' button on the help menu * Fix for crashes on some simulator views * Minor UI adjustments for better readability * Added handling to prevent crash when trying to use the commands under the 'more' button on the scanner page when the system doesn't support the command. * WiFi (NetworkManagement) page should now properly disconnect instead of giving the 'unexpected disconnection' message. * Added pressure display to the GreenFeed page * Added a fix for keyboard issues seen on some older tablets ** now possible to select alternative keyboard type(s) if the keyboard is missing decimal point input ** inputs are now validated to ensure that they do not have unexpected symbols. * Added confirmation dialog when selecting the 'reprogram concentration sensor' command when connected to a GF unit.

* Fix issues with SSF jam reporting. * Minor changes to improve stability when connecting to multiple systems. * Adds support for controlling the fistula attachment for GreenFeed units. ** The GreenFeed simulator now shows the fistula attachment as a capability. * Some small UI changes.

* fixes compatibility issues between the app and newer versions of the auto-calibration software.

* Adds support for connecting to GreenFeed Auto-Cal boxes. ** supports specifying a new network to connect to, as well as changing the Feeder ID the box is associated with. * Add checkbox to allow ignoring warnings while zeroing or spanning scales.

* move filter and sorting options to the menu bar ** sorting now defaults to ascending order by ID * Fixed a bug with the zero/span calibration code which wasn't running validation checks. * Added a hard-cap of 5 units connected at once, with a soft-cap and warning when connecting to 3 or more units. ** The soft-cap warning can be disabled for the current session by checking a checkbox displayed along with the warning.

* adds sorting and grouping functionality for the scanner view. ** feeders can be sorted in ascending or descending order by feeder ID number. ** feeders can be grouped by feeder type (i.e. GreenFeed, SmartFeed, etc.). *** sorting influences grouping order (i.e. GreenFeed units have lower ID numbers than SmartFeed units).

* Fixes compatibility between the app and feeders running older software versions. * Adds a 'Log View' to the help menu to allow viewing logs at runtime. * small graphical changes to improve interface readability. * Adds additional features available when connected to a feeder running the latest version of the software (updates to feeder software will be rolled out separately). ** Zero and Span operations will warn if voltages/masses are in an invalid configuration. ** Adds a 'factory reset' button to the 'more commands' menu on the scanning page. ** Adds a per-scale 'factory reset' button when performing a zeroing operation and the voltages are in an invalid state.