Minor enhancements and bug fixes.

Minor bug fixes and enhancements

Minor bug fixes and enhancements

Minor bug fixes and enhancements.

Minor bug fixes and enhancements

Minor bug fixes and enhancements

Minor bug fixes and enhancements

- Add support for CROSSFIRE device firmware V38R12 - Minor bug fixes and enhancements

Minor enhancements and bug fixes

Minor bug fixes and enhancements

Minor bug fixes and enhancements

Minor bug fixes and enhancements.

Minor bug fixes and enhancements.

Version 3.6.0 is a major update that adds support for connecting to CROSSFIRE devices with the latest firmware versions. It is important to install this update to ensure correct operation when connecting to devices with the latest firmware. This update also includes enhancements and fixes for when connected to devices running older firmware. ** New Features and Major Enhancements ** Support for Latest Firmware - Connecting to and configuring devices running firmware v38R09 is now supported Improvements to Compressor Setup - When connected to a device configured as a compressor, the app can now configure the device to run in a discrete control mode - Support for configuring the device with a high-pressure unloader - Support for configuring a device set up as a compressor to run with a flywheel installed Enhanced Troubleshooting and Diagnostics - Added support to display extended warning code under `System Status` to assist with identifying non-critical operating faults - Added support for measuring and calculating motor and power lead resistances to assist with device setup - Added support to set and retrieve a 9-character ID user-specified name for the device ** Minor Enhancements and Bugfixes ** - Miscellaneous small bugfixes ** Etc. ** Thanks to all our users for using our app to configure your CROSSFIRE devices. To make a bug report, feature suggestion, or to provide other feedback on your app experience, please drop us an email at info@lcotechnologies.com

Bug Fixes and Minor Enhancements Improvements to Compressor Curves • Resolved calculation error when scaling deadband between user entered PSI value and used RPM value in firmware. • Resolved an issue where the minimum RPM value would change after saving compressor curve settings. • Reversed order of data entry in the interface to entering deadband width first, then minimum speed. The range of acceptable values for minimum speed are dependent on deadband width and therefore, deadband must be entered first to prevent minimum speed changing from user defined value. • Resolved issue where incorrect compressor pressure curve was displayed in some scenarios

Version 3.5.0 is a major update that adds support for connecting to CROSSFIRE devices with the latest firmware versions. It is important to install this update to ensure correct operation when connecting to devices with the latest firmware. This update also includes many enhancements and fixes for when connected to devices running older firmware. Improvements for Colour Blind Users: Users with colour blindness had reported difficulties reading some error and warning messages displayed in the app. Updates have been made to correct this. • The colour of error messages has been changed to make them visible to colour blind users • Contrast increased for both error and warning messages, improving their visibility for all users Enhanced Data Display for Motor Control: • When connected to a device configured as a compressor, the app will now display the measured system pressure alongside the system speed Major Changes to Compressor Setup: Device firmware V38R08 has brought major changes to how compressors are set up, and the app has updated to reflect this. • The proportional guard band has been replaced with a proportional dead band to be more in line with user’s expectations of primary function as a relation to PSI rather than RPM based band. • For users connected to devices running older firmware, the guard band settings have been move from "Automation" to "System Setup" • Drain valve control settings have been moved from the auxiliary controls section of "Automation" to "System Setup" • Changes have been made to default compressor curves, and to allowed ranges of values for custom compressor curves. Due to variations in the output of some pressure transmitters and in the resistances of wiring setups, some devices were not seeing a full 5V signal at full pressure. According, the maximum stop pressure for curves allowed by the app is now 49PSI for 50PSI transmitters, and 98PSI for 100PSI transmitters. Vibration Detection: Recent device firmware updates have added a new vibration detection feature to improve system stability. Support for this has been added to the app. • On devices that support it, the app will automatically turn on vibration detection while making any changes to device configuration • Display of whether vibration detection is enabled or not has been added to "System Setup" Enhanced Troubleshooting Features: Improvements have been made to the diagnostic and troubleshooting information displayed in the "System Status" section. • Device firmware revision number is now displayed alongside firmware version number • The System Diagnostics section now supports display of more status codes, and includes detailed text descriptions for certain statuses • The Fault Record section is now always visible, and includes reporting of more possible fault codes. Detailed descriptions for all fault states have been added. Features for Power Users: Improvements have been made for users who interact with their device through the "Terminal" view. • The reference documentation has been updated to include features introduced by the latest device firmware • Users can swap between the two firmware versions installed on their device with a terminal command Minor Enhancements and Bugfixes: • Minor changes to the layout of some sections, to provide better information flow for phone users • Changes to the rate at which some values are updated in the app, to improve UI responsiveness • Minimize the number of commands that get re-sent to the device after a system reboot is detected • Fix a reboot loop that could occur sometimes when applying a configuration template • Fix a file permissions issue on iOS17 that prevented some configuration templates from being loaded • Miscellaneous small bugfixes Thanks to all our users for using our app to configure your CROSSFIRE devices. To make a bug report, feature suggestion, or to provide other feedback on your app experience, please drop us an email at info@lcotechnologies.com

Fixes an issue that was causing Bluetooth connection problems for some users on iOS17.

- Better report generation - Minor bug fixes and enhancements

Minor enhancements and bug fixes.

Minor enhancements and bug fixes.

Minor enhancements and bug fixes.

Minor enhancements and bug fixes.

Minor bug fixes and enhancements.

Minor bug fixes and enhancements.

Minor enhancements and bug fixes