Atlas • Improved rhythm display accuracy on Atlas Junior and Baby by ignoring slight compressions (≤10 mm Junior, ≤6 mm Baby). • Resolved PSIMV mode issues: PSync now saves correctly, pInsp changes send properly, and switching PSync updates all controls. • Added ventilator settings to Scenario Events: parameters can be viewed, edited, and synced directly from event cards. Camera • Enhanced NIBP display and logging: values now appear in exported videos, redundant logs removed, and event labels simplified. Corpuls • Improved pacing display: C3 shows correct pacing lozenge; C1 applies continuous therapy with visible ‘STIM’ label. • Fixed Scenario Review Timeline for accurate playback. • Updated German translations: “Cancel” → “Abbr.”, “Demand” in uppercase, “Schrittmacher” → “Schrittm.” CPR Band / CPR Puck • Added Bluetooth signal strength (RSSI) logging to detect interference. • Logs now show “OK” or “Warning” based on signal stability. Hamilton T1 • Aligned Facilitator settings with Hamilton T1 parameters for consistent operation. • Adjusted ranges, increments, and validations for all key controls. • Improved spontaneous rate and I:E ratio interaction for stable timing. • Standby timer now starts only after a ventilation cycle. • Alarm settings retain correct values when switching modes or patient types. • Neonatal alarms reset to defaults and display valid limits. • Resolved overlapping Pressure Alarm dials to maintain proper top/bottom order. • Improved Trends tab and submenu behavior for smoother navigation. • Menus now close automatically when entering Standby. • Fixed I:E ratio display in SIMV+ and PSIMV+ modes. • Ventilation and ExpMinVol values display correctly with one decimal and retain settings after weight or alarm changes. • Adjusted PEEP/CPAP dial so max indicator appears only within valid range. • Patient type switching now resets values correctly; “Last Patient” retains defaults. • Resolved alarm dial overlaps for proper display order. Nihon Kohden – EMS1052 • Fixed CPR elapsed time reset and “Restart CPR” timing (now 10 s). • Improved Japanese Cardioversion messages with corrected layout and font. • Added suspend time messages: “Suspend 10s,” “20s,” and “Restart CPR 30s” appear during pauses and clear on resume. Scenarios • Added 100+ training scenarios: 73 Adult, 17 Paediatric, 13 Neonatal. • Organized under new folder structure; existing scenarios unchanged. Multiple Hardware • Fixed “No connected device” message display after disconnecting all devices. • Added automatic Bluetooth reconnection after unintended disconnects. • Manual disconnects remain user-controlled. • Renamed devices retain connections with consistent log updates. Multiple Screens • Fixed behavior when electrodes or pads are disconnected. • Heartbeat sounds and rate alarms now stay inactive until proper connection.

Atlas CPR feedback now displays correctly on supported additional monitors when the primary monitor is connected to a CPR device. Resolved crashes that occurred when selecting CPR Console as an additional monitor while the primary monitor was connected to a CPR device. Fixed crashes during compressions on Schiller Defigard and Physiogard monitors when they were used as additional displays. Corrected CPR logging on Atlas Adult Gen 1 and Gen 2 manikins so recoil depth values now record accurately instead of always showing “-1.” Corpuls Corrected DEMAND mode message when ECG electrodes are removed; the message now properly states “No ECG cable in DEMAND mode” instead of “Pause.” Fixed AED text and voice prompts when switching from Monitor mode so they remain consistent with the pie chart state. Restored the “Perform CPR” voice prompt when returning to AED with the pie chart running. Adjusted Start Auto Analysis so AED prompts. Resolved an issue where AED voice prompts could still be heard while the device was in Monitor mode. Replaced “Up” and “Down” text buttons with arrow icons on Pacing intensity and frequency screens, and improved how adjustments respond to arrow key input. Updated arrow icons in soft key buttons, the Settings menu, and the Manual Defib energy selection screens for clearer consistency across the interface. Improved German translations for Advanced ICP Controls, Advanced PAP Controls, and multiple clinical or monitoring terms. Added missing translations for Imported Image and Imported Video labels. Corrected casing for the USE OFFLINE button and resolved translation inconsistencies for Urine – Ketones. Standardized terminology where existing German translations were unclear or inconsistent. CPR Band Added detailed logging for CPR band activity, making it easier to identify issues and improve troubleshooting during use. Facilitator Updated default ETCO₂ to 39 and respiratory rate (RR) to 12 in both Control and scenarios. Updated the REALITi Welcome Scenario and quick start scenarios to use these new values (changes apply if “copy default scenarios on startup” is enabled and the app is restarted; any custom scenarios remain unaffected). Nihon Kohden – EMS1052 Added translations for the 12-Lead ECG button and front panel in Japanese, Spanish, French, German, Portuguese, Italian, Polish, and Romanian. Adjusted layout to ensure all translated text displays correctly. Updated AED and Pacing label styling for better visibility. Fixed a display issue in Manual mode where the compression graph incorrectly appeared during energy charge when no CPR device was connected. Corrected HR value display so numerics no longer shrink when highlighted in Large and Normal views, and restricted highlighting when the ECG source is PAD. Improved CPR assist visuals: bars now show the correct starting compression depth, bar width and height have been refined, and grey bars were added for clearer release and compression feedback. “CPR Good Compressions” now displays on a white background, with turquoise bars when compressions meet correct depth and rate, while other bars remain red. Improved spacing for compression values, “CPR-Comp,” and “Tempo /m” labels to ensure consistent readability. Fixed ETCO₂ display in Control when connected to EMS1052: removed the incorrect third “pale” eye state, leaving only OFF (grey with line) and ON (blue without line). Toggling the ETCO₂ eye now correctly updates waveform and text visibility for both ETCO₂ and RR together. Lifepak 15 Joule settings for cardioversion shocks now remain at the last manually entered value (for example, 100 J) instead of auto-escalating for subsequent shocks. Maintenance Upgraded the Instabug iOS SDK to version 16.0.2 to maintain stability and compatibility with upcoming iOS releases. Zoll X Advanced Heart rate and pulse rate alarm parameters now adjust correctly when switching patient mode to Pediatric or Neonate.

Atlas Pulse settings now remain consistent across manikins, even after disconnection or monitor changes. Age profiles replace manikin type for clearer management: Adult, Paediatric, and Neonate set directly in the scenario panel. Alarm limits and CPR settings sync automatically with the selected age profile. Facilitator panels act only as remote controls, with the monitor managing and sharing settings. Corpuls Pacing mode in C1 improved: Mode button active, selectable Demand/Fix modes, clear prompts, and full German translations. Added confirmation prompts for pausing, resuming, and switching off pacing, with German translations. Electrode handling in C1 improved: ECG waveform now disappears when pads are disconnected, correct prompts are displayed, and switching leads in defibrillator mode is more reliable. Pacing clarity enhanced: added warning beeps, flashing alarm lights, clear on-screen alerts, refined Demand/Fix behavior, and full German translations for all pacing messages. Simplified settings by removing unsupported escalation protocol on C1 and C3. Fixed ECG curve issues: curves remain consistent when changing leads or modes, reset correctly on power-off, and unnecessary options removed. Fixed audio issues in Pacer mode on C3: removed incorrect prompts and metronome carryover. Top ECG curve in AED/Manual modes on C3 now fixed to ECG only, with lower curves freely configurable. Fixed alarm activation in C1 for vital signs outside limits, improving reliability of messages and sounds. Fixed C1 Send button so CPR and analysis are no longer interrupted. Facilitator / Control Improved stability with auto-reconnect, clearer connection lost messages, and better handling of disconnect/reconnect scenarios. Hamilton T1 PEEP and Plimit handling improved: correct limits, alarms, and display markers. TI dial increments corrected: +0.01 up to 1.0, then +0.05 after. Spont Set Point default set to 40, with proper adjustment controls. Added Respiratory Set Point to simulate spontaneous breathing response to CO₂ levels. Spontaneous effort now stops if ETCO₂ falls below the set point. Added quick buttons for adjusting both Spont Effort and Set Point. Corrected Flow Trigger dial limits for Adult/Pediatric and Neonatal modes. Fixed Flow Trigger display so the Off option appears correctly depending on the mode. Waveforms and numerics now update instantly instead of only once per breath. PEEP changes now display correctly during both inspiration and expiration. Pressure-controlled modes now respond more accurately to PEEP adjustments. Flow trigger now checked in real time, with spontaneous breath markers appearing at the true trigger point. Nihon Kohden - EMS1052 Fixed ECG2 and CPR waveform display issues, ensuring proper alignment on smaller screens. Updated Japanese translations across CPR messages, vital signs, alarms, and patient info. Improved CPR feedback: added “CPR Good Compressions” message, refined depth/rate prompts, and alternating guidance. CPR bars and feedback now restricted in Child mode, with clear messages shown. Added CPR assist waveforms and graphs, including compression depth/tempo bars and CPR numerics in Monitor mode. Expanded translations for AED, Manual, and Pacing modes, patient info, shock messages, and pacing prompts. Improved overall Japanese language coverage and accuracy. Translation Improvements Added Romanian language support. Zoll Fixed a crash when opening Patient Info on Zoll X screens used as additional monitors.

Atlas * Fixed Atlas Adult Wifi Config showing wrong manikin type. * Fixed wifi settings not updating for Atlas Adult Gen3 * Fixed wifi config not disconnecting after restart manikin. * Fixed not able to open wifi config settings for Atlas Adult Gen3 * Fixed Atlas Adult Gen3 compression depth mapping table

Atlas Fixed manikins on old firmware not getting correct type Additional checking of manikin types Depth parameter changes with multiple CPR devices attached Fixed timeout Increased timeout to 7 seconds for Atlas Baby, Junior, AdultGen3 Fixed pulse level setting not reflecting pulse level CPR artefacts appear on ECG trace when using Atlas SpO2 waveform changes to Poor Perfusion when ventilation or compression is started Camera Fixed waveforms not running on camera screen Corpuls Removed energy escalation protocol settings (C1, C3) Improved C1 invert display Stopwatch responds to scenario pauses and resumes Fixed C1 QRS tone disappearing when in either defibrillator or pacer modes and C3 QRS tone disappearing when switching from home screen to defib modes Analyse and Charge buttons activate AED and Manual Defibrillator modes, respectively Fixed CPR button showing no artefacts on the Pacing rhythm Pacer off prompt appears while pacing is on when changing from Monitor mode to AED or Manual defibrillator Resolved “Connect pacer cable” appearing in C1 Removed middle soft key option at the start of AED including during CPR phase and second soft key option ‘Manual’ to ‘Energie’ in Manual mode Fixed visible soft key options when charging or charged in Manual mode to only have Energy, Cancel and Monitor in both EN and DE Resolved Metronome setting text in AED and Manual modes Resolved pacing rhythm in Demand mode when only pads are on Extra checks on RA or LL electrodes as part of the pacing rhythm state to ensure it affects pacing rhythm Corrected pacing rhythm not affected by pads when off Improved how the rhythm with pacing reacts when either electrodes or pads are removed and then re-attached Fixed text prompt for Pacing when switching to defib Fixed ‘Switch off Pacer?' transitions when the switch is cancelled while electrodes are off Added translation ‘'Schrittmacher ausschalten?’ Fixed C1 audio doubling voice prompts Improved C1 Views Facilitator/Control Fixed primary folder appearing empty when it’s not Added multiple lines for scenario names Generic Fixed Sync not getting disabled after a shock Hamilton T1 Removed ‘Connect Ventilator’ button Fixed default Delta P value Fixed spontaneous breath marker not being removed at start and end of trace Spont TI is automatically calculated Improved calculations of default TI when changing Adult IBW or Neonatal Weight Improved IBW/weight calculation for the Vt alarm limit Improved the SPONT mode by disabling the option and setting value to 0 in Ventilator settings Fixed Pressure cmH2O alarm limits on high and low for Neonatal and Adult Improved alarm ExpMinVol default limits’ calculation from weight/IBW, Vt and Rate Corrected ExpMinVol low and high limit values for each patient type Fixed ExpMinVol low and high limits where it skips the maximum limit value Fixed fTotal high and low limits where shows Adult limits instead of Neonatal Fixed Vt limit low value skipping value 10 before the Off symbol for Adult Fixed Vt limit high value to show maximum of 3000 for Adult before the Off symbol FixedVt limit high value to show maximum of 300 for Neonatal before the Off symbol Fixed Vt limit low value to show maximum of 0.1 for Neonatal before the Off symbol Improved Vt limit low value calculation based on weight or IBW Fixed Alarms limits' where the high value can get lower than the low value Improved Rate and TI values Fixed dial subtext Improved TI max dot Added indicator for Nebulizer when it’s active Added message “Nebulizer is active” Created 10-sec timer for the generic message display Added a stop action for the Nebulizer to remove message and turn off light indicator Nihon Kohden - EMS1052 Improved Japanese translations Phillips MRX Display CPR waveform on all leads when CPR is active Teaching Management System (TMS) Fixed data computation, depth guide, and compression target rendering Zoll X Advanced Adjusted label sizes so translations fit appropriately

Camera Fixed waveforms not running on the camera screen. Atlas Fixed CPR artefacts not appearing on ECG trace when using Atlas.

Atlas Added support for Atlas Adult Next Gen Implemented Atlas Baby bootloader firmware update. It will only update if there is a new firmware MCU app update Corpuls Corrected texts to “corpuls simulation” Corrected "VT/VF possible" translation in DE for C3 Improved metronome automatic start settings for manual defibrillator and AED, to display correct metronome setting when switching between AED and manual defibrillator Set the on state default value to Adult 30:2 for the automatic start of the metronome in both manual and AED settings CPR Band Updated CPR recommendation statement for CPR device renaming Updated renaming rule to accept only the new naming format Facilitator/Control Added a randomiser for the Arterial line to be in effect when the line is inserted while RR value is zero. Resolved crashing when ‘HOLD TO SPEAK’ is tapped while recording Added a message in the User Recordings window to indicate when no recordings are saved Disabled the 'HOLD TO SPEAK' button during recording or until the recording is saved or discarded Added ‘HOLD TO SPEAK’ button in dark mode Updated UI for ‘New Recording’ menu when recording Added prevention on selecting other Sounds categories while recording Changed how User Recordings and New Recording appear, selecting User Recordings now will show both together Hamilton T1 Resolved the issue of Neonate weight dial minimum value lowering the minimum value of Vt past the limit. Set up the default value for parameter Rate to depend on IBW (adult) or weight (neonatal) values Adjusted Neo SPONT mode limits to Basic, More and Apnea options Improved Neo SPONT mode values Resolved the issue of the Standby Screen becoming unresponsive after pressing the Power button while a parameter dial is active (orange) Activated Tools window button Initialised Tools window Added initial Utilities and Configuration tabs including contents Updated Neonatal UI options in Standby mode Added the three Neonatal quick setup buttons Created the Neonatal dial with default of 2.0kg and allow weight adjustment Improved Last patient tab UI with ability to recall the last patient data Corrected the default Last Patient tab on first load of Standby Initialised Events window Nihon Kohden - EMS1052 Created a simulated CPR waveform Added CPR waveform in AED, Manual and Monitor modes (comp bars excluded) Added CPR elapsed time including how it resets when a new CPR device connection is established Resolved Pad messages appearing behind the CPR guide lines Updated the JA text display ‘Do 5 more chest compressions. Do not touch patient’ in AED by removing an unnecessary symbol Resolved the issue of multiple texts appearing on Press Scale options while in JA language Resolved the issue of ‘Use Disposable Pads’ voice overlap with ‘Press AED button’ Added restriction to the use of the charge button when Pads are off Resolved the issue of “CPR Assist” message appearing in Pacing even when there is no CPR assist connected Corrected the EN text display ‘Do 5 more chest compressions. Do not touch patient’ in AED by removing an unnecessary symbol Resolved the issue of waveforms (EtCO2, SpO2) resetting after Send is pressed from Control Initialised behaviour for Alarm slider’s up and down arrows when it reaches the limit by changing it to a light grey colour when they become ‘disabled’ or ‘off’ Zoll Resolved where Zoll monitors were experiencing crashes after switching from a different monitor with VT/VF alarms occurring before or after the switch Added 8-sec timer in Zoll X monitors to close defibrillator window and return to home screen after a shock is delivered Multiple Screens Resolved parameter values for vitals: HR, SpO2, ETCO2, etc. not updating correctly Translation Improvements Updated Brazilian Portuguese translations Added adjustments to Zoll X, LifePak 15, and CPR Console to ensure Brazilian Portuguese translations fit appropriately Updated Simplified Chinese REALITi Translation

Facilitator/Control * Added hiding of subfolders in slideout scenario list on control and scenario new start Menu / main screen * Renamed 'Stage' to 'Monitor' in the main menu Multiple Screens * Fixed sounds muting when opening the app from the background * Fixed waveforms becoming laggy when doing a UI action causing the QRS sound to be incorrect timing for HR. This mainly affected older iPads * Added 0.5 second delay for shock button presses on all defibrillator when sync is on Translation Improvements * Added Brazilian Portuguese translation corrections Corpuls * Updated C1 AED/Manual voice and text prompts for EN and DE * Stop media players in sound managers when checking therapy electrodes * Change the float menu for defib to exclude some options * Changing the rotary knob when it’s in AED * Added German translations * Add VF/VT alarm in Corpuls3 * Modify VF/VT in defib mode to not show Hamilton T1 * Fixed the Rate dial not increasing in PCV+ mode * Added Print Screen for * Battery indicator and icon improvements * Added the Screen Lock feature to Hamilton T1 Nihon Kohden - EMS1052 * Removed unnecessary Large Numerics' text displayed in waveform line * Resolved lead waveforms lines not showing correctly when disconnected * Improved CPR Assist CPR messages * Fix issue Press menu blank * Fix issue in Large Numeric * Technical and guidance messages improvements * Fixed crash related to translations in the Patient information area preventing startup. * Removed the Temp1 Check Sensor message on start when starts without cable plugged in to match the real machine. * Added miscellaneous improvements for the parameter alarm sliders and window Zoll R * Resolved the issue of Pacer spikes not appearing on the Zoll R screen

Atlas Handled manikin ages for the following monitors CPR feedback dashboard: Zoll X Series/Advanced/Propaq MD, Zoll R Series, Generic Defib, Schiller Defigard 7. CPR depth ranges can be customized on control Handle age changes for center compression feedback and compression depth Corpuls Fixed a bug on the C3/C3T where Demand mode was possible with no electrodes attached Re-added 'Stimulation fortsetzen' to C3 Pacing Resolved the issue of 'Start Analysis Automatically' setting from C3 affecting C1 text prompts display Added correct text translation “PreShock CPR durchführen” for C3 Corrected text prompts ‘Analyse starten’ and ‘Start Analysis’ for C1 Improved Pacer pause and continue pacing prompts Amended Pacer pause and continue pacing DE translations Resolved the issue of being unable to charge after powering on with the manual button Resolved the issue of overlapping DE voice prompts while the “Patient nicht berühren” prompt was playing Resolved the issue of prompting the user to start analysis when it was not required after a shock delivery during the switch from Manual to AED Resolved the issue where the pie chart gets reset incorrectly during a switch from Manual to AED (vice versa) while charging; the pie chart reset will now only occur if it is fully charged Facilitator/Control Resolved the issue of ART/BP line showing zero values in Generic screens Added support for multiple scenario folder levels Hamilton T1 Added a ‘Feature not Simulated’ popup to the O2 enrichment key for Hamilton T1 Added the day/night toggle for Hamilton T1 Lifepak 15 Added preShock CPR user input in LIFEPAK 15 Settings Added preShock CPR in LifePak15 Added preShock CPR duration restrictions: values 0-14 are considered Off state, values 15-30 activate preShock, and values above 30 are capped at 30 Set preShock CPR duration default at 15s Implemented printing out of waveforms currently displayed on the screen Resolved the issue of ‘Shock Advised’ audio overlap Resolved the issue of “Analyzing now--Stand clear” text abruptly flashing when Analyze button is pressed during a CPR countdown Nihon Kohden - EMS1052 Default lead sources in different modes improvement Added CPR assist linkage icons Created connectivity status for connected and disconnected CPR device Added temporary static CPR-Comp image for CPR device connections for AED mode only Fixed screen reloading when switching between modes Resolved the issues of 12-Lead ECG waveforms not appearing properly in other smaller iPad screens Improved translations for the Nihon Kohden EMS 1052 Resolved the issue on Lead change in 12-Lead ECG where it displayed incorrect and incomplete leads Improved Lead changes when switching to 12-Lead ECG where it will change source Pad to II and other leads will remain as is Corrected lead source when switching from Large Numerics to 12-Lead ECG

Atlas * Informs the user if wifi change is successful or not for Atlas Baby * Changed the WiFi change result message to be multiline * Added support for extended mac so the WiFi scan works with the new firmware in Atlas Baby * Fixed message in Atlas Baby about new update when on WiFi not showing * Fixed disconnect issue at end of update in Atlas Baby * Improved update speed in Atlas Baby * Added firmware update for Atlas Baby * Updated Atlas Baby firmware to 1.4.8 Corpuls * Resolved the issue on cardioversion settings where Autosync is not set as default setting in both C1 and C3 * Corrected order of mode selection to Async, Sync and Auto Sync in both C1 and C3 * Fixed C1 - Double up of voice prompt to press analyse * Fixed C1 - No oximetry pulse tone * Corrected translation “Schrittmacher ausschalten?” * Added the missing text after a shock is performed in Manual defibrillator, ‘Shock performed - Perform CPR’ in both EN and DE * Changed pie chart symbol to shock (lightning) symbol in C1 * Added pause and resume features on AED/Manual defibrillator’s elapsed and pie chart timers of C1 and C3 for scenario pauses * Applied pause and resume features on C1 and C3 pie charts for scenario pauses * Created timer reset features on C1 and C3 power buttons * Resolved the issue on AED/Manual defibrillator timers not resetting when switching between monitors from Control Nihon Kohden - EMS1052 * Resolved the issues on overlapping alarm messages of IP disconnections. * Added Zero CAL message limitations - messages will disappear when calibration is done * Added STAT mode * Assigned STAT as default when Patient type is changed * Initialised oscillation graph images to NIBP process - generic images only * Added cancellation of NIBP calculation when Manual is ready to shock or when AED analysis has started * Fixed small glitch on rendering dash line affecting some monitors * Resolved the issue of incorrect paper positioning on different screen sizes * Fixed the issue where the paper comes out from a different area when scrolling is used * Added second tab in Press menu - alarms to be improved in later tickets * Created a priority of display for CO2 and ART line since REALITi supports more than two sockets - other Critical Care added will not be displayed unless one of the two is disconnected * Resolved the issue of the ‘More Setup’ button toggles the IP tab when clicked * Resolved the issue of ART showing up in Press even when disconnected * Corrected Press current tab highlight(blue) on selection * Added Zero Cal for secondary IP attachments * Added Press Label for second socket * Allowed enabling back of used Press Label when an IP is disconnected * Improved the More Setup menu for the second label, with correct tab repositioning when disconnected * Improved IP label removal in the More Setup menu when the priority CO2 connection is established LIFEPAK 35 * Resolved issues on the bottom menu not displaying correctly after a shock in AED Multiple Screens * Fixed fluctuating HR on slower iPads Zoll X * Changed EtCO2 to be off by default

Atlas * Corrected icon for Atlas Baby Wifi Config. * Confirm dialog added to ask before changing to the firmware update screen. * Applied random variation to the ventilated volume. * Set no reply on pulse command for Atlas Baby/Junior. Corpuls * Resolved the issue of missing text and voice prompts in C1. * Updated translations * Added C1 text translations for ‘Ready for charging’, ‘Manual Defibrillation Mode?', ‘Press Analyse’ and 'Analysing heart rhythm’ * Added C3 text DE translations for the AED and Manual * Updated QRS/PT mute icon * Added ‘PT’ text to show as QRS/PT * Resolved the issues on configurations not retained after changing scenarios or windows. * Improved function on softkey “Views” where it will reset configuration back to default including selecting the current view. * Added voice file for “Assess heart rhythm * Added symbols on certain texts in both AED and Manual * Changed voice and text from “Start analysis to “Press analyse” (AED) * Changed voice “Do not touch or move patient” to “Do not touch patient, analysing heart rhythm” (AED) * Changed text “Do not touch or move patient” to “Do not touch patient” (AED) * Changed text from “Shock performed” to “Shock performed, perform CPR” (AED and Manual) * Lessened playback delay on voice prompt “Perform CPR” to appear like a continuous voice prompt after a shock is performed (AED) * Changed text “Select Energy” to “Press Analyse” with voice prompt. (AED) * Changed text “Ready for shock” to “Press and hold down Shock key”(Manual) * Changed text “Select Energy” to “Select energy / Charge energy” (Manual) * Changed text “Select Energy” to “Assess heart rhythm” with the voice prompt when switching to Manual or when pie chart is full. * Corrected text for when shock is cancelled or CPR is continued to “Select energy / Charge energy” (Manual) * Added DE voice file prompts. * Added restrictions on Analyze and Shock buttons while HR eye button from Control is off for both Corpuls AED and Corpuls 3. * Applied the proper prompts when HR eye is off for both Corpuls AED and Corpuls 3 * Resolved the issue on Corpuls AED Analyse key flashing even though the Pads from Control is off. * Resolved the issue on both Corpuls AED and Corpuls 3 not recognising the state of eye from Control when switching between these screens. Lifepak 20 * Resolved the issue of crashing when the speed dial selects Patient’s menu from Options. Nihon Kohden - EMS1052 * Introduced support for the Nihon Kohden - EMS1052 Scenarios * Enabled scenario version 3 for web build of control. Ventilator Engine * Added a more realistic IE ratio to etco2 waveform. Zoll * Resolved the issue on Zoll monitors crashing (Zoll R not affected) when a CPR device is connected, and made improvements to other lines of codes. Zoll R * Resolved the issue on sync dots appearing in the second waveform instead of the first waveform. Zoll X * Resolved the crash issue on Zoll X when SimConnect and a CPR device are connected. * Fixed the most visible issues on UI overlaps on CPR and BVM windows.

ATLAS * Changed good compression rate from 90-120 to 100-120. * Streamlined the source code for CPR depth. * Resolved the issue on CPR depth values incorrectly displaying rounded numbers. * Fixed the issue on CPR Adequate depth line overlapping CPR Maximum depth line. * Fixed depth label cutoff in Zoll monitors. * Added pulse and HR to Atlas device settings. Corpuls * Updated Crowdin translations to include “Schocktaste gedrückt halten” and “R-EKG Vermessen”. * Corrected encoding to UTF-8 * Added “Connect therapy electrodes” audio prompts for both EN and DE. * Corrected DE audio files for “schock abgeben” and “schock abgegeben” * Changed timer symbol to pie chart symbol. * Corrected messages and voice audio prompts for “Do not touch patient. Analyzing heart rhythm” when the Analyze button is pressed. * Added new German voice audio prompts. * Added “Press Analyze” message and voice audio prompt when pie chart is filled. * Corrected translation for “Measuring D-ECG”. * Enabled ECG print on Print button. * Added restriction on Print button if D-ECG preview is on. * Added the missing Cancel button when shock is ready in AED. * Corrected effect of Cancel button on CPR pie chart. * Resolved the issue on the Perform CPR not getting activated after a shock disarms automatically. Zoll (incl. Zoll X) * Resolved the issue on Zoll monitors crashing (Zoll R not affected) when a CPR device is connected, and made improvements to other lines of codes. * Resolved the crash issue on Zoll X when SimConnect and a CPR device are connected. * Fixed the most visible issues on UI overlaps on CPR and BVM windows. Multiple Screens * Resolved the issue on the NIBP SEND where it toggles ART line when pressed. * Set Zoll ETCO2 connection as ON always without the need to toggle CO2 button. * Fixed the issue on Schiller Defigard/Physiogard Touch 7 and Tempus Pro where the SpO2 connection is not recognised when switching to these monitors. * Resolved the issue on LifePak20 SpO2 pulse bar not appearing on connection. * Corrected the LifePak20 “SpO2: Searching for Pulse” message to appear only when there is no finger connection. * Resolved the issue on monitors not showing the correct state of SpO2 when switching from a ventilator. * Resolved the issue of app crashing when swiping from the left to exit Mindray D3/D6 or Nihon Kohden EMS1052 while the AED is in process. * Added extra checks to prevent similar crashes in Mindray D3/D6, EMS1052 and LifePak35. Translation Improvements * Added translations for Polish, Estonian, Czech, Slovak, Korean. * Corrected translation for “Measuring D-ECG”.

Scenarios - Fixed the issue on textbox not getting added in a new Scenario. - Resolved the issues on custom scenarios not loading properly.

Atlas * Updated Atlas Junior compression depth mapping * Changed disconnect timeout fix for Atlas Junior to >V2 * Fix for better CPR artifact in Atlas Junior * Enabled firmware update to latest on connect for production * Fixed Atlas Junior/Baby not processing data stream after packets arrive too fast or not enough data in the packet * Added support for old Atlas Junior firmware * Enabled Atlas Junior firmware update for production build * Updated Atlas Baby’s adequate and maximum depth values * Fixed clearing of Atlas Junior/Baby wifi config from available list on scan * Rounding volume for Atlas Baby, removed random variation of volume for Baby/Junior * Reduced Junior firmware upload timeout * Increased wait time after Junior firmware upload before requesting restart * Added more compression idle checks for Junior/Baby * Added reset CPR on no data from Junior/Baby manikin * Added checks in Junior/Baby to reduce issue of abnormally high rate Corpuls * Modify defibDisarmed for AED to make it aedCprDidBegin every disarming * Added CPR Depth changes handler in C1 * Fixed adequate and max depth not reverting to original values after disconnecting manikin * Fixed overlapping lines and truncating labels * Fixed displaying “Deliver Shock” when it was unnecessary * Fixed Auto Analyse where it does not automatically activate after pie chart cycle * Fixed metronome turning off * Fixed staying in “Select Energy” * Improvements on metronome state during switches to and from AED * Set metronome default for both Manual and AED as Adult 30:2 * Adjusted the metronome after preShock to ensure the sound is correct for “Adult cont” or “Child cont” * Resolved voice prompt activating randomly during CPR phase after exiting and restarting the same monitor * Resolved incorrect buttons (Energy, 100, 200) appearing in AED SimConnect * Resolved additional monitor not showing the correct state of pleth based on the primary monitor * Fixed removal of available SimConnects on rescan when bluetooth disabled * Enabled SimConnect firmware update for production build * Fixed monitors crashing when attempting to connect to SimConnect Scenarios * ECG, Spo2, Etco2 and RR default visible state changed to off for new scenarios and existing scenarios keep existing behaviour of being on * Changed finger attached to be on by default Facilitator Control * Fixed selected Events not loading after update on new electrodes * Added 18 channel configuration for custom Event * Enhanced Electrode Placement to update based on monitor, displaying 12 or 18 channels * Changed Quick Placement and Manual Placement * Enabled switching between Anterior and Posterior views * Enabled new electrodes in Manual Placement and Quick Placement * Adjusted UI to be suitable for smaller screens Defigard Touch 7 * Resolved Defigard Touch 7 crashing when electrode placement is changed * Fixed crash from removing 12 leads and pads before scenario starts in Defigard Touch 7 Lifepak 20 * Resolved memory leaks that slow performance Lifepak 15 * Added ART option in Channel 2 and Channel 3 for waveform * Fixed Co2 numeric not blinking when outside of alarm range Zoll X/Advanced * Set Pads as default trace * Added Pads as an option in the Quick Access Key: Lead TMS * Resolved exported video not getting the correct RR and Temperature values * Resolved ETCO2 and RR showing inaccurate values during preview * Fixed NIBP getting hidden when changing parameters Translations * Updated The Netherlands translations CPR Depth Monitor * Resolved monitor with CPR device crashing upon connection with Control CPR Ventilation Monitor * Added scaling on ventilation bars and numeric label for max volume based on manikin type or parameter settings * Included a line for each max volume and set at 90% of the full scale * Enabled clipping of values greater than the full scale Multiple Hardware * Added disconnecting all connected devices on closing app

**New Features** CPR Ventilation Monitor * Added scaling on ventilation bars based on manikin type or parameter settings. * Added numeric label for max volume based on manikin type or parameter settings. * Incl. a line for each max volume and set at 90% of the full scale. * Enabled clipping of values greater than full scale. CPR Depth Monitor * Added CPR depth configuration from Control on Zoll X Series, Zoll X Advanced, Zoll Propaq MD, Corpuls 3, Zoll R Series, Generic Defib and CPR Console. * Enabled conversion of units for compression depths. * Improved CPR bar displays for compression depths. * Adjusted CPR bars to match CPR depth values. * Fixed monitor with CPR device crashing upon connection with Control. CPR Depth Control / Facilitator * Added CPR depth configuration in Parameter Settings * Added conversion of units for Adequate Depth. * Added conversion of units for Max. Depth. * Added CPR manikin type drop down option for Automatic, Newborn, Child and Adult. CPR Depth * Fixed compression depth values not updating properly when switching to another monitor. * Fixed issue on adequate compression depth value not displayed in the correct level. * Fixed monitor crashing when switching to other monitors while Atlas Junior is connected. * Corrected Corpuls3 and Corpuls 3T values showing zeros instead of the default values. **Improvements** Atlas * Increased length of low RR CO2 when using SimConnect or Atlas manikin for ventilation. * Fixed Atlas CPR not affecting HR. * Added manikin data recording (Currently debug builds only) * Added CPR depth configuration from Control on Zoll X Series, Zoll X Advanced, Zoll Propaq MD, Corpuls 3, Zoll R Series, Generic Defib and CPR Console. Enabled conversion of units for compression depths. Improved CPR bar displays for compression depths. Adjusted CPR bars to match CPR depth values. * Added partial support for Atlas Baby. * Fixed AED not working from “movement detected” due to compressions state not ending. * Made connect process for Atlas Junior same as in 11.6.0. * Cap data of Atlas Junior. * Added extra values in Atlas Junior compression lookup table. Corpuls 1 * Fixed Hamilton T1 where the alarm continues after quitting a scenario. * Corrected therapy socket influence on electrodes. Corpuls 3/3T * Fixed issue with metronome count not reverting to original configured ratio. * Fixed issue with Start Analysis being played just after powering on, no delay. * Fixed issue with metronome not resetting to Adult 30:2 when C3/C3T is powered off. * Fixed memory leak in Corpuls 3/3T which resulted in a crash when used with Hamilton T1. Defigard Touch 7 * Added parameter field flash on NIBP, Temp, ETCO2 and RR when values are off limits. * Enabled flash on bigger NIBP field. * Improved priority alarms to show in the alarm status field properly. * Corrected precedence of alarm message from any parameter over “ECG: Cable not detected” message. * Added “ECG: VF/VT” if HR alarm still persists for a certain period of time for any patient type. * Included “ECG: Asystole” message when HR is 0\. * Improved alarm light to change from orange to red if alarm is for VF, VT or Asystole. * Improved alarm light to show orange for medium and low alarms. * Fixed Pulse field not flashing when pulse is off limits. * Fixed “SpO2: Pulse off limits” message issue from not appearing when there is a pulse rate alarm. * Integrated pulse alarm limits to the alarms; value on the pulse will now determine whether to show the alarm based on these limits. Hamilton T1 * Fixed Hamilton T1 where the alarm continues after quitting a scenario. Multiple Monitors / Screens * Fixed the additional monitor not showing the correct state of pleth based on the primary monitor. * Fixed ECG waveform not being changed if the new waveform was the same as the previously loaded scenario. Zoll R * Fixed Filtered ECG not getting deactivated by Control.

Multiple Screens - Improved logs window performance when lots of logs. - Enabled unit measurements' conversion in IBP and NIBP of the following monitors: Zoll R, Philips MRx, Schiller Defigard Touch7, Generic Monitor, Generic Defib, Generic Wave, Generic Numerics, GE Carescape B850, Philips IntelliVue MX800 and WelchAllyn Connex. - Monitors that do not support the conversion to unit cmH2O will remain as mmHG. - Resolved issue in Schiller Defigard Touch7 where NIBP value gets changed by the conversion toggle button in CO2 in Unit Measurements - Enabled Pacer Settings' Default Output and Rate for Zoll Propaq MD, Zoll X, Schiller Defigard Touch 7 and Tempus LS. - Enabled Pacer Settings' Remember Last Output and Rate for Zoll Propaq MD, Zoll R, Zoll X, Schiller Defigard Touch 7 and Tempus LS. - Fixed ECG waveform not being changed if the new waveform was the same as the previously loaded scenario. Capnostream 35 - Resolved crash issue on starting Capnostream 35. Corpuls 3/3T - Fixed issue with metronome count not reverting to original configured ratio. - Fixed issue with Start Analysis being played just after powering on, no delay. - Fixed issue with metronome not resetting to Adult 30:2 when C3/C3T is powered off. Hamilton T1 - Changed F Total b/min from decimal to integer in Alarms. - Changed F Total b/min from decimal to integer in the Monitoring section. Lifepak 15 - Resolved issues on NIBP countdown timer and MAP display overlap. - Enabled reset on contrast when the monitor is turned off. - Resolved issues with the Home and high-contrast Sunvue buttons, where the lower portion was unresponsive to clicks. - Resolved crash issue when changing back from high contrast Sunvue display to color display. - Resolved issue on metronome. - Enabled correct state for CPR button when switching from AED to manual defibrillator. Revel Vent - Resolved issue on audible tone looping after swiping from left to exit the ventilator. Schiller Defigard Touch 7 - Enabled flashing alarm light and parameter field flashes in the secondary Pulse field when limits are - exceeded. - Enabled alarm light flash for HR. - Added heart icon in the second Pulse parameter field - Fixed primary Pulse background to blue when changing from HR to Pulse. - Resolved issue on secondary Pulse not changing to dashes when Control’s finger probe is off. - Resolved issue on HR, SpO2 and Pulse not flashing in both alarm light and parameter fields when limits are - exceeded. - Fixed issue on primary Pulse not changing back to HR field when the source is AUTO and becomes unhidden. Zoll R - Resolved issue on “NIBP MEAS ABORTED” message appearing when NIBP value in Control Parameter Settings is changed.

Logs - Added ventilation logs to the log window. (was previously in dev only generic ventilator). Facilitator - Fixed Ventilator tab heading going over the top of the Monitor popup. - Added a switch in the Ventilator tab and Advanced Respiratory controls to disable the ventilation modeling for SpO2 and EtCO2. RR will still reflect what is selected on the ventilator. Additional Monitors - Fixed crash caused by reconnecting to the monitor. Schiller Defigard/Touch 7 - Corrected waveform fields display including ECG labels when pads or leads are OFF. - Corrected the differences between HR Source Auto and specific ECG Curves List sources to display their respective sources. - Fixed ECG waveform visibility conflicts with SpO2 and ETCO2. - Fixed bug on Auto Scale that incorrectly changes label of selected source. - Fixed bug on Amplitude that incorrectly changes label of selected source. - Corrected HR source display when Pads is OFF. - Corrected display for first waveform field to show no line when disconnected from Control. Corpuls 3 - Fixed CPR prompt audio duplication. - Fixed volume icon's display for both presses and dial turns. - Added yellow bars for deep compressions. - Added CO2 as second waveform in AED/Manual mode. Corpuls 1 - Fixed out of memory crash.

New Features: - No new features. Improvements: Translations - Updated German translations. Facilitator - Fixed flatlined pleth in preview. Schiller Defigard/Touch 7 - Corrected Control connections on electrodes and pads with HR source: Auto and Defi. - Corrected waveform label display for HR source. - Enabled prioritising ECG source when HR source set in Auto. - Corrected display values for HR and Pulse parameters. - Added ECG messages on connection and disconnection. - Added SpO2 messages on connection and disconnection. - Fixed HR measurement field to stay visible even when disconnected. - Corrected HR value when disconnected. - Enabled heart symbol in HR measurement field. - Enabled SpO2 module in Pulse parameter. - Added SpO2 sound level. - Fixed HR and SpO2 sound source including parameter display. - Removed SpO2 sound changes pitch in settings. Lifepak 15 - Added Temperature parameter. - Enabled connection to Temperature in Control. - Enabled ability to change units in Control’s Parameter Settings. - Added Temperature parameter in Speed dial selection. Zoll X-series/R-series - Fixed shock button with Sync releases shock. - Fixed missing charge level view when shock is disarmed. Zoll Propaq M/Propaq MD/X-series - Enabled message and progress indicator for NIBP Auto. Mindray D3 - Fixed yellow alarm 3 tones every 20 seconds.

Bug fixes and performance enhancements

Bug fixes and performance enhancements

Bug fixes and performance enhancements

Bug fixes and performance enhancements

Bug fixes and performance improvements

Connections Panel & Facilitator - Added additional menu items to monitor and control within the facilitator screen. This will remotely open the connections panel on monitors. Zoll R - Improved trace options / defaults - PADS as source removed from PACER mode - Added Advisory Function messages - Improvements to SpO2: - Corrected waveform from being flatlined on load - Corrected SimConnect probe connection - Added SpO2 notification messages for connection status - Added SpO2 delays closer to actual device - Fixed elapsed time to reset after turning off - Added Pacer Detect icon - Added Enable / Disable button interactivity for Pacer Detect - Removed other traces in Pacer mode except Trace 2 - Added Alarms' titles SimConnect - Fixed SpO2 display on reconnect with SimConnect on generic monitor - Fixed a bug where SpO2 waveform would not show when probe connected Mindray D3 & Mindray D6 - Fixed language inconsistencies with D3 and D6 Mindray D3, Mindray D6 & Zoll X - Added AED language settings Corpuls 3 - Metronome is now audible when charging - Added timer to remove power off prompt if nothing selected in 10 seconds - Added ability to remove power off prompt when other modes are selected - Fixed power off prompt from getting stuck after restart - Fixed function of cancel button Corpuls 1 - Removed Pleth waveform and replaced with CPR feedback in defib mode - Removed alarm in AED mode Corpuls AED - Fake CPR band Slow/Shallow option is now detected as movement Capnostream 35 - Fixed waveform display Atlas & Atlas Junior - Added battery level and charging indicator for Atlas manikins

Zoll R - Added settings to support 3 leads, filtered ECG, SpO2 and EtCO2 based on settings - Updated labels and layout to support 3 leads - Corrected pacing to single trace - Renamed Leads to ECG - Renamed Filt ECG to FIL - Improvements to display when using Trace 3 with CPR - Modified prompts that were obstructing waveforms - Adjusted pacing output to increments of 2 instead of 5 - Fixed overlap on Trace 3 with Sync on - Corrected sync background colors when defib is on - Improvements to EtCO2: - Added zeroing - Adjusted timers - Added CO2 warm up - Corrected EtCO2 button behaviour - Changed ECG sync symbol from S to triangle - Settings - Added settings for Trace 2 and 3 Zoll X - Correct missing display elements when in high contrast mode Zoll EMV - Enabled two-way control - Tidal volume, Fi02, BPM, and mode changes on the device can now adjust the facilitator Schiller Defigard Touch 7, Schiller Physiogard Touch 7 & Zoll X - Improvements to IBP alarms and timers - Added ability to zero art. line LIFEPAK 15 - Fixed UI glitch that caused a thin line on CO2 tracing Corpuls 3 - Disabled jog dial flash when device is turned off - Improved pie chart on manual defib and AED - Enabled Cancel button after Analyse button is pressed - Improvements to manual defib timer and pie chart - Resolved an issue with waveforms not editable after switching to manual mode Corpuls AED - Fixed an issue with analysis running when not expected. - Updated analysis button LED states to better replicate the device Corpuls 1, Corpuls 3, Corpuls 3T & Corpuls AED - Handled Empty fields in manual mode Facilitator - Fixed missing positions for manual electrode placement on iPad Mini - Resolved an issue with patient weight and temperature not displaying correctly when activating scenarios - Improved Chinese translations SimConnect - Improvements to connection, finger detection and stacked breaths - SimConnect is no longer displayed as a CPR band - Fixed bug that caused ETCO2 to trend to 0 after ventilation - Added ability to change name of SimConnect - Added interface for selecting adult or neonatal flow probe SimConnect & Zoll X - Corrected handling for trace of SpO2 after probe disconnected - Added labels to Zoll X to support SimConnect: - Check sensor - Initializing - Calibrating - Searching - Corrected SpO2 start up behaviour to support integration of SimConnect Settings - Fixed overlapping text in settings drop downs - Resolved an issue where settings were not saved correctly Atlas Junior - Enabled pulse during compressions - Removed unnecessary quotation marks from WiFi config Atlas facilitator - Connections panel: - Updated name to “ATLAS”, previously “ATLAS Senior” - Added ability to see WiFi SSID in connection settings