Screenshots

Description

RF Control remotely controls up to 24 channels of Sennheiser* and Shure* wireless receivers in one application, side-by-side. The intuitive user interface provides a quick overview of the most vital parameters of your wireless receivers.

Dedicated screens have been carefully developed to give you control to parameters that are relevant in a live situation while securing access to the ones that might be harmful to the safety of the system.

Following devices are supported by utilizing the manufacturers remote control protocols:
Sennheiser: EM 3732*, 2000* series and evolution G3 and G4* wireless receivers.
Sennheiser: EM 6000 receivers
Shure: Axient*, ULX-D*, QLX-D*

Depending on the manufacturer of the receiver wilSmoTe supports monitoring of the most relevant parameters including:

- RF level bargraph (all)
- AF Level bargraph (all)
- Battery status information (all)
- Remaining battery time (Shure with Li-Ion battery, EM6000)
- Device name (all)
- EQ type (2000 and ewG3)
- Command settings (EM3732COM)
- AF Out level (all)
- Squelch level (Sennheiser)
- Mic Offset (Shure, EM6000)
- Lock Status (Shure, EM6000)
- Encryption Status (Shure, EM6000)
- TX Type (Shure, EM 6000)
- TX RF Power (Shure)
- LQI (EM6000)
- Capsule type (EM6000)
- Warning indicators
(Sennheiser: Low Bat, RX Mute, TX Mute, RF Mute, AF Peak, NoLink, Encryption mismatch)
(Shure: Low Bat, Interference, RX Mute, TX Mute, Enrcryption mismatch, AF Peak)

A plot of the RF and AF levels is displayed over time, making it the perfect companion for walk tests and spotting dropouts in your audio.

The full screen plot window of the iPad version allows to scroll through the recorded RF and audio levels to look up for problems and drop-outs even after hours of recording.

All relevant parameters can be remotely controlled:

- Frequency, bank, channel (all)
- Device name (all)
- EQ type (2000 and ewG3)
- Command type (EM3732COM)
- AF Out level (all)
- Squelch level (Sennheiser)
- RX Mute (Shure)

iPad only:
The scan window allows you to use one of the recognized Sennheiser devices to scan the RF environment. The frequency plot can be used to drill down the spectrum and look for free frequencies. Scan is not supported by Shure devices.

iPad only:
With the additional ScanPacks the scan data can be stored as *.csv file and uploaded to your personal Dropbox or sent as attachment via email. The *.csv file I can be loaded from third party software for frequency coordination and planning. Either ScanPack will unlock the RF Inspector for sample accurate readout of the scan data at your fingertips.

During start up RF Control will scan your network for connected devices. For Sennheiser 2000 series and evolution wireless G3 devices Firmware 1.7.0 or higher needs to be present on the receivers to support the remote control protocol.

The app can monitor up to 24 channels in mixed configurations. The device list allows access to all devices in the network and selection of 24 devices for monitoring.

The order of channels can be freely arranged and will be restored at the next start of the app.


Notes:
RF Control is the new name of the wilSmoTe app.
RF Control does not support IEM transmitters!
Channel count depends on hardware performance - 24 channels requires iPad Air 2 or newer - manual activation in app settings required

Sennheiser, EM 6000, EM 3732, 2000 series, evolution G3 / G4 are brands, products or trademarks of Sennheiser electronic GmbH & Co.KG and not associated in any way with RF Control.

Shure, ULXD, QLXD, Axient are brands, products or trademarks of Shure Inc. and not associated in any way with RF Control.

What’s New

Version 2.5.4

In some cases the cycle scan would not cycle but just stop after first run on ewG4 and EM 6000

Ratings and Reviews

1.8 out of 5
5 Ratings

5 Ratings

zabaluyev ,

Not working at all.

I will change star rating and comments right after the software will start to work at least.
I was trying to connect to the system of sennheiser 3000 systems, which was described as working with the software, for the whole day with no success. WSM was working fine. So the problem is inside the software.

Kidaguirre ,

Don't waste your money.

The app won't even load and then when it does it lasts for a couple mins but you can't access anything or add anything.

Mikesv ,

Needs a little work

Seems a little buggy sometimes. I'm getting a message that I cannot connect but the app works for a while then stops working.
It's ok when it's working.

App Privacy

The developer, Claus Menke, has not provided details about its privacy practices and handling of data to Apple. For more information, see the developer's privacy policy.

No Details Provided

The developer will be required to provide privacy details when they submit their next app update.

Information

Seller
Claus Menke
Size
25.6 MB
Compatibility

Requires iOS 8.0 or later. Compatible with iPhone, iPad, and iPod touch.

Languages

English

Age Rating
4+
Copyright
Price
$2.99
In-App Purchases
  1. ewG3ScanPack $0.99
  2. EM37ScanPack $0.99

Supports

  • Family Sharing

    With Family Sharing set up, up to six family members can use this app.

More By This Developer

You May Also Like