EL tools: Circuit Calculator
Quick calcs for circuit design
Free · Designed for iPad
No more resistor math by hand. Dividers, combined resistance, RC transients, LCR filters, op-amp gain, and a programmer calculator, all in one app.
All the everyday calculations for electrical design, in one app.
When you're designing a circuit, small questions keep coming up:
"Will this resistor pair give me the voltage I need?"
"What's the rise time of this RC circuit?"
"What do three resistors in parallel add up to?"
"Where is the cutoff frequency of this filter?"
"Which resistors give this amplifier a gain of 10?"
"What is 0x3F8 in binary?"
Too small to open a spreadsheet, but you want the answer right now.
EL tools is a practical calculator for electrical design that lets you check these things quickly on your phone.
■ Voltage Divider
Enter the input voltage and target output voltage, choose a standard resistor series (E6/E12/E24/E48), and instantly find the R1/R2 combinations closest to your target.
The min/typ/max output voltage is shown for each combination, taking resistor tolerance (and input voltage tolerance) into account.
See not just the ideal voltage, but the real range you can expect with actual component tolerances.
Useful for power supplies, voltage references, ADC inputs, and other divider designs.
■ RC Step Response
Calculate the time constant τ = RC from the resistance and capacitance.
View the rise (charge) or fall (discharge) curve as a graph, and check the voltage at any elapsed time with a slider.
Handy for early-stage work on reset circuits, delay circuits, smoothing circuits, and switching circuits.
■ Combined Resistance
Supports series and parallel connections.
Calculate the nominal, minimum, and maximum combined resistance from up to three resistor values and their tolerances.
Great when you want to build a target value from resistors you have on hand, or check the result including tolerance.
■ LCR Filter
Calculate filter characteristics from R, L, and C values.
For a 1st-order RC low-pass filter, see the time constant and cutoff frequency. For a 2nd-order series RLC filter, see the cutoff frequency and damping ratio.
The frequency response is shown as a Bode plot, so you can understand the filter's behavior at a glance, not just as numbers.
■ Op-Amp Gain
Choose an inverting or non-inverting amplifier, enter the target gain, and find the Rf/Rg combinations from a standard resistor series (E6/E12/E24/E48) that come closest.
The min/typ/max gain is shown for each combination, taking resistor tolerance into account. A circuit diagram shows where each resistor goes.
■ Programmer Calculator
Convert values between HEX, DEC, OCT, and BIN at a glance.
Tap individual bits to toggle them, and choose the word size (8/16/32/64-bit) and signed (two's complement) or unsigned.
Run bitwise operations (AND, OR, XOR, NAND, NOR, NOT, shifts, rotates) and arithmetic, then feed the result back in to keep going.
Handy for register settings, bit masks, and decoding communication data.
■ Useful for
- Checking values while designing circuits
- Choosing resistor and capacitor values
- Designing voltage dividers for power circuits
- Checking RC delay times
- Working out series/parallel resistor combinations
- Checking filter cutoff frequencies
- Choosing gain resistors for op-amp circuits
- Working with register values and bit masks in firmware
- Quick calculations during prototyping and debugging
- Electronics hobby projects and learning circuits
Quick answers for those "let me just calculate this" moments.
Not complex enough for a full simulation, but you still want the result on the spot.
EL tools supports your day-to-day electrical design work with simple, straightforward controls.
Ratings & Reviews
- This app hasn’t received enough ratings or reviews to display an overview.
- New: Op-Amp Gain. Find standard resistor pairs (E6–E48) for a target gain in inverting and non-inverting amplifiers.
- New: Programmer Calculator. Convert between HEX, DEC, OCT, and BIN, toggle bits, and run bitwise operations (8–64-bit, signed or unsigned).
The developer, KAZE Application, indicated that the app’s privacy practices may include handling of data as described below. For more information, see the developer’s privacy policy .
Data Not Collected
The developer does not collect any data from this app.
Accessibility
The developer has not yet indicated which accessibility features this app supports. Learn More
Information
- Seller
- TORU YAMAGUCHI
- Size
- 8.3 MB
- Category
- Utilities
- Compatibility
Requires iOS 15.0 or later.
- iPhone
Requires iOS 15.0 or later. - iPad
Requires iPadOS 15.0 or later. - iPod touch
Requires iOS 15.0 or later. - Mac
Requires macOS 12.0 or later and a Mac with Apple M1 chip or later. - Apple Vision
Requires visionOS 1.0 or later.
- iPhone
- Languages
- English
- Age Rating
4+
- 4+
- Contains
Advertising
- Copyright
- © KAZE Application