FIXED: Lean and slope were wrong, and are now rebuilt from scratch - Lean could read 8 to 15 degrees on a dead-straight road and stay there for most of a ride. Parked upright it looked fine; the error only appeared once you were moving - Slope had the same fault in the other axis: it could report a climb of over a degree while the road was visibly dropping, and three other sensors agreed it was dropping - Both are now worked out from the puck's gyro, the bike's own wheel speed and the barometer, instead of from the motion chip's internal angle calculation — which was found to invent tilt that its own accelerometer contradicted at the same instant - Measured across six recorded rides: lean on straight roads went from as much as 9.8 degrees off to within a degree, and on the worst ride the time spent reading more than 10 degrees of lean while travelling straight fell from 47 per cent of it to none - Slope now agrees with GPS altitude where it used to disagree, and no longer reports grades no road has What lean can and cannot show - Lean is worked out from the turn you are making, so it shows how far the bike is over through a corner - It does not show you shifting your weight, or the camber of a straight road, and it never will: a bike held in a steady corner feels gravity straight through itself, which is what stops it falling over. Nothing that senses gravity can read lean mid-corner — not this puck, not a dearer one - Parked upright it still reads level, so it remains a check that a mount zero worked Rides you already recorded - Rides already in your library keep the numbers they were recorded with. Only rides recorded from this version on carry the corrected ones - Nothing was thrown away: the angle the motion chip reported is still recorded beside the corrected one, in the ride file and in CSV exports Tripper Puck - Settings now shows which protocol version the puck is speaking, and says plainly when the app is older than the puck and some of what it sends is going unrecorded — previously a newer puck was read perfectly and its extra data silently dropped, with nothing on screen to say so - The puck's raw accelerometer and its count of discarded sensor reads are now recorded into your rides and written to the .trip and CSV exports, alongside the gyro and calibration Knowing which build you are running - Settings now shows the app version, the date the build was made, and a note you can write yourself — useful for recording which puck firmware a build was paired with

NEW: Rides in iCloud Drive - Every finished ride is now saved to a Tripper folder in iCloud Drive, so your rides are no longer only on the phone - Open the folder from Files on any device, or from a Mac; each ride is a .trip file carrying everything — route, speed, lean, g-force and heart rate - To put one back into Tripper, import it the way you would any ride file - Copies go one way: Tripper writes rides out and never changes what's already in your library. Turn it off in Settings if you'd rather not use the iCloud storage Finishing a ride - The name box now suggests where you set off as well as when — "Manhattan · 2 Aug 14:43" rather than the date on its own. Type over it, or clear it to go back to just the date - Skip now does what it says: it asks, then discards the ride. It used to save it anyway under the default name, so there was no way to throw away a ride you hadn't meant to record Select and export several rides at once - Tap Edit in Rides to pick as many rides as you like — or Select All — then send them out in one go as .trip, GPX or CSV - Delete a batch the same way, with one confirmation instead of one swipe per ride Lean, beside slope - Your lean angle now sits next to slope on the same card, at the same size — live while you ride and again in replay - The side reads L or R rather than a minus sign, which is easier to take in at a glance on a moving bike; below a degree it doesn't claim a side at all - It doubles as a check that a mount zero worked: parked upright, it should read Lean with no side - The card no longer shifts and resizes as the numbers change Tripper Puck - Fixed: if the puck went quiet without the phone noticing the link had dropped — after the puck rebooted on the bike's power, for instance — Tripper kept believing it was still connected and never tried to reconnect, so the rest of the ride was recorded on phone sensors. It now spots the silence and reconnects by itself - Fixed: a puck on the newest firmware could look disconnected, and a ride recorded in that state had no puck data in it at all. Tripper now reads a puck newer than the one it knows about instead of refusing it - Zeroing the puck's mounting angle now tells you whether the puck accepted it — pending, confirmed, or no response — instead of only confirming your tap - Settings shows the puck's IMU calibration, so you can see how confident it is about which way is down before trusting a lean reading - The puck's own gyro and calibration are now recorded into your rides and written to the .trip and CSV exports, alongside the phone's

NEW: Bluetooth heart-rate sensors - Tripper now connects to any standard Bluetooth heart-rate sensor — a chest strap (Polar, Garmin, Wahoo…) or a sports watch broadcasting heart rate, like Garmin's "Broadcast Heart Rate" mode - Turn it on in Settings: it pairs with the first sensor it finds, reconnects to that one from then on, and shows the live reading right in Settings; Forget lets you switch sensors - While the sensor reports, its reading is what's recorded and shown — live on the dashboard, in replay and on the ride chart. The Apple Watch still works exactly as before and takes over whenever the sensor isn't reporting - Heart rate synced into Apple Health by other apps (Garmin Connect, for example) is also stitched into your rides after the fact, filling any gaps Tripper Puck - Regen braking level from the bike is now recorded and shown — live in Settings, and in replay next to battery, power and ride mode - Tripper recognises which puck it is talking to, so a Light puck (the CAN-only build, no GPS) keeps your phone as the position source instead of reporting a fix that is never coming

NEW: Tripper Puck (DL1) support - Tripper now connects to the Tripper Puck, a bike-mounted sensor that streams GPS five times a second, lean and slope measured on the bike itself, and air temperature - While the puck is connected, its readings are recorded instead of the phone's; if it drops out, your phone takes over within seconds and a warning tells you - The puck's marker button drops a pin on your ride — glove-friendly, and the puck's screen confirms every press - Every sample notes which sensor recorded it, plus satellite count and GPS quality from the puck - Turn it on in Settings; a chip on the dashboard shows the link and satellites, and a temperature sticker joins the slope card Dashboard improvements - Speed readouts show whole numbers everywhere — easier to read at a glance - The map turns to face your direction of travel in 2D as well as 3D - Landscape: slope and temperature now sit beside the info panel, with the puck link in the top corner - Steadier layout: readouts no longer shift as the numbers change Fixes - The watch workout now ends reliably when your ride ends — it could previously keep running (and keep reading your heart rate) long after you finished

NEW: Heart rate from your Apple Watch - Recorded alongside speed, slope and g-force, and shown live on the dashboard, in replay and on the ride chart - Starts automatically: the watch workout begins from your phone when a ride starts — no tap on the watch needed — and Tripper keeps trying and reconnects for the whole ride - Readings are recorded on the watch and stitched into your ride by timestamp, with gaps filled from Apple Health after the ride; if none is coming through, an on-screen warning lets you fix it mid-ride - Rides are saved to Health as workouts, so they credit your activity rings NEW: Apple Watch complication - Add Tripper to your watch face: trip time ticks live while you record and freezes while paused — one tap opens the app NEW: Import rides - AirDrop, share, or open a .trip or .gpx file straight into your library — Tripper appears in the share sheet and the Files app - A .trip carries the whole ride; a .gpx brings the route, and speed, distance and grade are worked out from it New landscape layout - Turn the phone sideways for a driving-style dashboard: full-screen map with a panel for speed, time, distance, altitude, slope, heart rate, g-force and heading - The same layout in replay, with the timeline along the bottom On the map - 3D map option for riding and replay, with an adjustable tilt slider in Settings - Smoother camera follow while riding Better replay - Switch map style and 3D while playback is running - The camera stays locked on the rider at every speed — no more catching up in steps - Slope readout added, matching the live dashboard Plus - Slope gets its own instrument card under the dashboard - Review charts now use the full width of the screen - Many small layout fixes