New • Brand-New Creation Flow — The App's main scenario is quickly print a piece. This release turns it into a step-by-step flow that starts with choosing a substrate, so you can create directly on it. 1. Choose a Substrate • Built-in substrate presets: Includes eufyMake official substrates and commonly used substrates. Add one directly to your project to get its size, contour, material, and color. • New personal substrate: For standard geometric substrates, enter the dimensions manually — or scan a substrate to start creating. • Save substrates you've used: Save frequently used substrates to your personal substrate library for reuse anytime. 2. Content Creation • Design directly inside the substrate contour: Simpler and more intuitive on a phone screen. • AI Skills: Pick a Skill, upload your photo, and generate a one-of-a-kind customized piece. 3. Print & Design and Material Reminder • 3D craft preview: Preview the craft effect right on the substrate's 3D model — rotate your phone for an interactive preview. • Adjust crafts together: Adjust the craft settings of different layers together on a single page. • UV DTF film: Choose UV DTF film and sticker mode is selected for you automatically, with the UV DTF sticker printing flow explained. • Material reminders: Smooth substrates get a reminder to apply pre-treatment; soft materials get a reminder to use flexible ink. 4. Print Alignment • Recommended alignment and placement: Suggestions based on the substrate type you choose — friendlier for beginners. • Local snapshot: Printing on a large flatbed? Capture only the area you need — much faster for small substrates. • Auto alignment: Place the substrate you chose earlier on the printbed, and your design automatically aligns to where it sits in the snapshot. More New Capabilities • Bidirectional printing: The App now supports bidirectional printing. • Cleaning Cartridge Level Estimate: The cleaning cartridge details page now shows estimated levels for the cleaning solution, moisturizing solution, and waste ink compartments, so you can check remaining levels anytime. You'll get a reminder when any compartment drops below 30%, giving you time to prepare a replacement. • Three Moisturizing Modes: Maintenance settings now support Auto, Flexible, and Storage modes. Flexible Mode adjusts moisturizing behavior based on whether you plan to print within the next 48 hours, helping reduce moisturizing fluid waste. Storage Mode is designed for longer periods of inactivity and starts a moisturizing cycle immediately to protect the printhead. Auto Mode keeps the existing moisturizing behavior. • Expired Ink Confirmation Entry: A new entry on the Device Status page lets you review risk information for expired ink and confirm the device status. Once confirmed, related features become available again and ink levels display normally. • Enhanced Deep Clean: Manual Deep Clean now offers Standard and Enhanced levels, reducing the risk of printhead clogs. • Unit switching: Switch between mm / inch. Other Improvements • Numeric input: Type numbers in directly — no more pop-up. • Crop: View and crop to a specific size. • Layer dimensions: Select a layer and its size is always visible. A Naming Update for the eufyMake App and Studio Along with these updates, we also want to share a naming change. As Anker brings its product lines, including eufyMake, together under one unified Anker brand, eufyMake App and Studio are getting new names: Anker Make App and Anker Make Studio. While the names are changing, everything you know and use will stay the same, including your account, devices, projects, and existing features.

New • Brand-New Creation Flow — The App's main scenario is quickly print a piece. This release turns it into a step-by-step flow that starts with choosing a substrate, so you can create directly on it. Choose a Substrate • Built-in substrate presets: Includes eufyMake official substrates and commonly used substrates. Add one directly to your project to get its size, contour, material, and color. • New personal substrate: For standard geometric substrates, enter the dimensions manually — or scan a substrate to start creating. • Save substrates you've used: Save frequently used substrates to your personal substrate library for reuse anytime. Content Creation • Design directly inside the substrate contour: Simpler and more intuitive on a phone screen. • AI Skills: Pick a Skill, upload your photo, and generate a one-of-a-kind customized piece. Print & Design and Material Reminder • 3D craft preview: Preview the craft effect right on the substrate's 3D model — rotate your phone for an interactive preview. • Adjust crafts together: Adjust the craft settings of different layers together on a single page. • UV DTF film: Choose UV DTF film and sticker mode is selected for you automatically, with the UV DTF sticker printing flow explained. • Material reminders: Smooth substrates get a reminder to apply pre-treatment; soft materials get a reminder to use flexible ink. Print Alignment • Recommended alignment and placement: Suggestions based on the substrate type you choose — friendlier for beginners. • Local snapshot: Printing on a large flatbed? Capture only the area you need — much faster for small substrates. • Auto alignment: Place the substrate you chose earlier on the printbed, and your design automatically aligns to where it sits in the snapshot. More New Capabilities • Bidirectional printing: The App now supports bidirectional printing. • Cleaning Cartridge Level Estimate: The cleaning cartridge details page now shows estimated levels for the cleaning solution, moisturizing solution, and waste ink compartments, so you can check remaining levels anytime. You'll get a reminder when any compartment drops below 30%, giving you time to prepare a replacement. • Three Moisturizing Modes: Maintenance settings now support Auto, Flexible, and Storage modes. Flexible Mode adjusts moisturizing behavior based on whether you plan to print within the next 48 hours, helping reduce moisturizing fluid waste. Storage Mode is designed for longer periods of inactivity and starts a moisturizing cycle immediately to protect the printhead. Auto Mode keeps the existing moisturizing behavior. • Expired Ink Confirmation Entry: A new entry on the Device Status page lets you review risk information for expired ink and confirm the device status. Once confirmed, related features become available again and ink levels display normally. • Enhanced Deep Clean: Manual Deep Clean now offers Standard and Enhanced levels, reducing the risk of printhead clogs. • Unit switching: Switch between mm / inch. Other Improvements • Numeric input: Type numbers in directly — no more pop-up. • Crop: View and crop to a specific size. • Layer dimensions: Select a layer and its size is always visible. A Naming Update for the eufyMake App and Studio Along with these updates, we also want to share a naming change. As Anker brings its product lines, including eufyMake, together under one unified Anker brand, eufyMake App and Studio are getting new names: Anker Make App and Anker Make Studio. While the names are changing, everything you know and use will stay the same, including your account, devices, projects, and existing features.

• Continue Printing with Expired Ink — When printing with expired ink, confirm the risk in the dialog to keep printing. Replace all ink within 14 days and your Care benefits remain unaffected; reminders continue if it's not replaced in time. • Soft White Ink Reminder Upgrade — When printing with standard white ink in scenarios where Soft White Ink is recommended, the dialog now includes a Continue Printing button so you can proceed after acknowledging the risk, with an option to snooze reminders for 3 months.

New • White Ink Settling Repair — When the system detects that white ink may have settled, it automatically triggers a repair process to restore uniform ink distribution, reducing print quality issues caused by white ink settling. • Medium Clean Level Upgrade — Medium Clean is now split into two levels. The new Enhanced level provides better repair for print line dropout issues, allowing you to choose the cleaning intensity that best fits your print head condition. Improved • Compatibility Improvements — Improved compatibility with older device models and operating systems.

New • AI Agent — Process images through natural language conversation, including style transfer, portrait generation, and artistic effects. Generate images directly in chat and import them to your canvas. Improved • White Ink Choke Improvements — White Ink Choke now adjusts automatically based on the local edge width of images or text, helping prevent fine details from becoming unclear due to excessive choking. Pure white layers and white objects automatically bypass choke to prevent white content from being eroded. For fine details like thin lines and text strokes, choke is automatically reduced to better preserve white ink. All protections apply automatically with no manual configuration needed.

New • Remote Shutdown & Moisturize — A Moisturize button has been added to the print head maintenance section on the device page, and a Shutdown button has been added in the device settings panel. Both can be used anytime when the device is not in operation. • Cleaning Cartridge Full Alerts — When the cleaning cartridge reaches its limit, a clear alert appears with options to moisturize or confirm replacement. Certain ongoing maintenance actions (Deep Clean, White Ink Switch, etc.) save a breakpoint and resume automatically after the cartridge is replaced. • Print Height Limit Raised to 13cm — The maximum printable object height has been increased from 10cm to 13cm. When using snapshot alignment and the object exceeds 60mm, a guidance dialog appears with a direct link to switch to zero-point alignment (which supports up to 130mm). • Maintenance Consumption Breakdown — An info icon (ⓘ) has been added next to the green extra-consumption numbers on the Ready to Print and print completion pages. Tapping it shows a breakdown of each maintenance action and its per-channel ink usage. • Camera Calibration — White paper detection has been added to the calibration flow, catching missing or misplaced paper early to improve calibration success rate. • Parts Expiry Reminder — When consumable parts (such as the cleaning cartridge) are approaching their expiry date, the app sends staged advance reminders to help you prepare replacements in time. • Software Update Improvements (App) — The app update flow has been improved for a smoother upgrade experience. • Software Version Rating — Starting from this version, after each update and print completion, you'll be invited at an appropriate moment to rate the current version. Improved • Device Status — When the device is in Maintenance Status (awaiting ink injection after deep clean or moisturizing), Auto Measuring and axis movement are now accessible. Printing remains blocked until ink is injected. • Maintenance Progress Indicator — Clean, Deep Clean, drain, auto deep clean, auto moisturize, and white ink cycle now show a progress bar with estimated remaining time. • ICC Profile Auto-Update Off by Default — The ICC profile auto-update option is now unchecked by default.

New • UV DTF Sticker Mode Guidance & A-Film Detection — A guidance pop-up appears the first time you switch to UV DTF Sticker mode. If height measurement exceeds 3.1mm, a warning alerts you that the A film may not be properly attached. • Initialization Preparation Page — A new pre-check step before initialization guides you through key preparation tasks, reducing initialization failures. Improved • Device Status Display — Status naming unified across App and PC. States including Initializing, Performing Maintenance, Calibrating, and more now show clear subtitles at all times. • White Ink Mid-Print Priming Notification — When cumulative white ink printing reaches 50ml, a notification explains the mid-print priming pause and confirms printing will resume automatically. • Simplified Device Settings — The "Remote Print" and "Repeat Print" switches have been removed. Both features are now always enabled by default. • Rotary Positioning Accuracy — The canvas origin has been moved to the top-left corner. Existing projects migrate automatically. • Skip Priming After Short Pause — If a print job is paused and resumed within 10 minutes (no cartridge change during pause), pre-print priming is skipped, saving ink and wait time.

Optimized - Contour Recognition & Batch Fill - Automatically detect contours and batch-fill print areas for faster setup. - Custom Auto Maintenance - Set auto-maintenance time and advance reminders in device settings. - Improved Alignment - Fine-tune zero-point offset manually for more precise printing. - Ink & Cleaning Cartridge Expiry Alerts - Alerts you before consumables expire to maintain print quality. - Background Removal Upgrade - Cleaner edges and more natural cutouts.

New - Ink and cleaning cartridge expiration reminder (14 days in advance) - Stop test print at mid-process - Hide elements in canvas - Horizontal/vertical flip elements in canvas Optimized - Low ink reminder with "Do not remind" option - Enhanced maintenance log with more records - Improved offline ink level display

UI redesign for more user-friendly interaction experience. New: - Skip Printing — Keep elements visible on canvas but exclude from printing. Optimized: - Simplified zero point calibration guide. - Added rotary printing knowledge base link.

Major update for printing efficiency and control. - New: Assisted Shot - Manual highest plane determination improves measurement accuracy compared to automatic detection. - Optimized: Continue on Low Ink — Support Reprint, Test Print, and Camera Calibration when ink level is below 10%.

This update brings major improvements to printing efficiency and control — introducing key features like Continue Printing After Low Ink Warning, Repeat Printing, and Print Countdown, along with smarter workflow enhancements throughout the app. - New: Continue Printing After Low Ink Warning — Users can now choose to continue printing after the device shows a 10% low ink warning, until ink reaches the minimum usable level. - New: Repeat Printing — After completing a print job, users can skip the photo-taking step and quickly start the next print. (The feature is off by default and can be enabled in device settings.) - New: Print Countdown — A visible countdown timer now appears on the print progress page. - New: Automatic Log Upload — With user permission, the program can automatically send error logs to help developers analyze and improve the experience. - New: Print Head Replacement Mode — When selecting to replace the print head in the consumables list, the device will enter a special state to assist with the procedure. - Optimized: Print Test and Camera Calibration — Redesigned guidance visuals and improved workflow help users complete these steps faster and more intuitively. - Optimized: Cancel Print and Photo Flow — Users who cancel a print job will no longer be required to retake photos upon returning to the editor. - Optimized: Roll Installation Guidance — Updated visuals and clearer instructions enhance the setup experience. - Fixed: Various minor issues.

- The community now features courses and events. Share & discover new ways to play with creators worldwide. - Optimized editor performance for smooth handling of large images. - Added batch project deletion. - Enhanced the guided process for print testing, calibration, and rotary printing. - Optimized the user feedback process on iOS and improved app stability.

We're thrilled to announce our app now fully supports the new eufyMake E1- the world's first personal 3D-Texture UV Printer! - Introduced an informative article about E1 during the device initialization phase. - Updated the printing test functionality - Text-to-Image model upgrade for better generation quality. - Fixed bugs

We’re thrilled to anounce our app now fully supports the new eufyMake E1 — the world's first personal 3D-Texture UV Printer! We’ve also redesigned the AI design tools and creative community to unlock richer UV printing experiences.

Fixed bugs.

AnkerMake renames it as eufyMake. All current services will remain uninterrupted.

Added User Experience Program After updating to this version, you can view the User Experience Program in Settings > About > Terms and Conditions.

1. Added a print failure diagnostic link on the print completion page. 2. Fixed bugs.

1. Added a new entry for AnkerMake official store. 2. Fixed bugs.

1. Added a reminder for when the filament used in the last G-code is different from the current one. 2. Optimized the text of some error pop-up windows that were difficult to understand.

1. Added a new entry for contests. 2. Added an upload feature for community prints. 3. Fixed bugs.

- Added a notification about the preheating of the printer when sending G-code to the printer or downloading G-code from Make it Real.

1. Explore has a fresh new look, seamlessly connecting with Make It Real's model community, bringing brand-new features such as categorized searching, sorting, commenting, and favoriting. 2. In the "Me" section, you can now earn points by completing tasks and exchange those points for rewards. 3. In-app slicing has been comprehensively optimized, significantly boosting file loading and slicing speeds.

1. Added a part lifespan maintenance feature for M5C. 2. Added a nozzle clog cleaning feature for M5C. 3. Upgraded the message center.