New controllers • Baldrick boards are now monitored like any other controller — status, firmware and board, temperature, uptime, free memory, and which protocols are actually feeding them, with dropped-frame counts when they matter. • Baldrick boards also work on the Testing tab: run the board's port identification pattern or any pattern you pick, test a single port on its own, and fire the board's effect presets (with a stop entry) straight from the Presets button. • Genius and Experience controllers running the 2.x firmware are supported. Detection, identity, playback detail, and eFuse warnings all work across both firmware generations. Better controller detail • Controllers with a KulpLights (or other branded) cape now show the cape vendor's logo instead of a generic platform image, on both the card and the detail page. • A new Cape section shows name, version, EEPROM version, serial, designer, what the cape provides, and a link to the vendor's site. • Pixel string outputs now show the full per-virtual-string wiring — pixel count, colour order, start channel, grouping, start and end nulls, zigzag, reverse, brightness and gamma — rather than just a description. Testing • A new "Apply to MultiSync remotes" option on a controller's testing section sends start, stop and test pattern changes out to its MultiSync remotes. • An "ALL ON" button sits beside "ALL OFF" for turning everything on at once. Read-only controllers are skipped. Much faster remote controller UI • Opening a controller's own web interface from away from home is dramatically quicker and no longer stalls. • Files a controller says are cacheable are now kept on disk (per device, up to 64MB, cleared from Settings), so revisits don't re-fetch them. • Page content is compressed across the internet hop — controller UI is roughly 5x smaller in transit. • Fixed pages hanging for 35 seconds: paths containing "+" or "#" now go through, two requests for the same page at once are both answered, and a request that can never be answered fails immediately instead of waiting out a timeout. • A controller found on your own network is now reached directly over the LAN rather than round-tripping through the cloud. Because the cache does the job properly for every controller vendor and firmware version, the 28MB of controller web files the app used to bundle are gone — the app is substantially smaller and no longer serves an FPP 10 controller an older version's pages. Overlay effect lists now always come from the controller itself, so they match the firmware that's actually running. Reliability • Fixed a case where a single malformed message could leave the app connected but silently stop receiving any device updates. • Devices over your plan's limit now show an upgrade tile instead of quietly disappearing. • Updated Google sign-in and various platform components. Plugin note: several of these need the FPPMon plugin updated on your FPP instances. The new plugin also cuts its polling load by about 80% and takes status straight from FPP 10's push feed, so it's lighter on your controllers.

Smarter, faster light mapping. • "Map from Lights" now uses our upgraded scanning engine for more accurate LED placement — even when the camera moves a little during the scan. • Scans are faster: detection passes now run in parallel. • FPPMon now figures out how many pixels are actually lit on a prop, automatically trimming dark or missing pixels at the end of a string. • More reliable decoding across a wider range of cameras and lighting. • General stability and performance improvements.

* Sign in with Apple ID or Google ID * Ability to discover/view/configure local FPP instances without the plugin installed * Ability to monitor WLED and Falcon v3 controllers * New "Testing" tab to make testing your display easier

* Fixes problem trying to invoke effects with the FPP 10 pre-releases * Coordinate with FPPMon on other devices to make sure the FPP instances aren't overloaded with update requests

* New Apple Watch Companion App * New Widgets for home screen * New ability to map lights directly to xmodel files

* New ability to start and stop playlists directly from the instance list * New page for configuring Overlay Model Effects for KulpLights controllers * New App Intents for starting playlist, presets, etc... from Shortcuts and Siri

* New ability to start and stop playlists directly from the instance list * New page for configuring Overlay Model Effects for KulpLights controllers * New App Intents for starting playlist, presets, etc... from Shortcuts and Siri

Initial support for FPP 8.0

Add support for remotely monitoring and configuring Falcon v4 and v5 controllers.

* Fixes some issue when moving from Wifi to Cellular data * Allows warning notification to display when the app is open

More bug fixes and performance updates....

* Fixes problems detecting KulpLights controllers purchased from other vendors * Fixes problems displaying WLED effects page when accessed from remote networks

Just a bunch of bug fixes and performance tweaks.